£2.20 exc vat
£2.64 inc vat
In stock
£2.20 exc vat
£2.64 inc vat
In stockRecommended usage 1 x DAM6140 to fit one mini.
complete set of metal locktabs for the gearbox only -see 18G8086 for the clutch.
Late cars did not have locktabs-just plain washers or bolts and locktite for safety on performance cars
Minispares centre own reconditioned helical gearbox with all new ball bearings
throughout except under 1st, 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc.3.1 diff fitted. ...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.2.9-1 diff fitted .any fa...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 1st, 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc.3.2 diff fitted .an...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 1st,2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.3.4 diff fitted .any ...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 1st,2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.3.1 diff fitted. Any ...
Mini Spares 'Straight Cut Close Ratio 4-Speed gearboxes'
Mini Spares are proud to offer a new range of straight cut, 4-speed rod change gearboxes.
These gearboxes undergo a full rebuild, using new; bearings, sea...
Mini Spares 'Straight Cut Close Ratio 4-Speed gearboxes'
Mini Spares are proud to offer a new range of straight cut, 4-speed rod change gearboxes.
These gearboxes undergo a full rebuild, using new; bearings, sea...
Minispares centre own reconditioned helical gearbox with all new ball bearings
throughout except under 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc. 2.7-1 diff fitted as ...
Mini Spares 'Straight Cut Close Ratio 4-Speed gearboxes'
Mini Spares are proud to offer a new range of straight cut, 4-speed rod change gearboxes.
These gearboxes undergo a full rebuild, using new; bearings, sea...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 1st,2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.3.4 diff fitted .any ...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc. 2.7-1 diff fitted as p...
Close ratio 4 speed helical gearbox using our C-STN48 gear kit.
1st gear ratio 2.583
2nd gear 1.644
3rd gera 1.250
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)
housing and deleted 1996 on.locking glue used such as locktite
All differential crownwheels used these locktabs. 3 required and if you need new bolts see ATA7043 (6 of.) All sold singly
The housing to retain the double row gearbox bearing has 4 bolt holes but the casing itself might only have 3 drilled holes where they deleted the susceptible to cracking hole on powerful engines. Originally 2 locktabs were used when four bolts, decr...
complete set of metal locktabs for the gearbox only -see 18G8086 for the clutch.
Late cars did not have locktabs-just plain washers or bolts and locktite for safety on performance cars
High quality version of 13H9513, INA branded.
Dual use bearing fits the end of the A Plus 18mm mainshaft where the 1st Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.
Kno...
IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...
Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
This is the second gear 28 teeth as used on many 3-synchro Mini gearboxes. Introduced during the late 850 production and continued in use thru the "S" gearbox with the 22G1100 laygear. If you are inspecting your old gears be sure to ch...
Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine NSK bearings
3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc
with tuflock patch to secure.
Used on all mainshafts with 14mm shaft end for the 1st motion shaft---when they went to the 18mm shaft on A plus gearboxes they used DAM7485 which is metric thread.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.