EYE ROD EXTENSION YOKE FOR GEAR LEVER
22G2792

£34.50 exc vat

£41.40 inc vat

In stockIn stock
Yoke for rod change geaboxes only. This sits inside the alloy gear lever housing on the selector rods and the gearlever ball end sits into this part. Use with 2x RPS1416 roll pins.

£34.50 exc vat

£41.40 inc vat

In stockIn stock

Recommended usage 1 x 22G2792 to fit one mini.
Rod Change Gear Shift Mechanism - Qty 1
Gear Lever and Selector Mechanism - Qty 1

Recommended products

This pin joins the gear change rod to the selector rod, behind the diff housing

case and is usually easier to remove when reverse is selected.In reverse gear the angle is easier for removal. This is a great time to fit the Mini Spares slick ...

People also bought products

Secondhand (used unit)only. This sits under the 28G251(DAM8488) alloy housing where the speedo cable connects to on the gearbox and the speedo drive pinion slots through this.Obsolete from Rover we are offering these old used units in ca...

Fits all minis except Autos and those with hardy spicer joints. It has the detent lug on for rod change R/H side. Sold singly.

These might be marked as 22G420 on the casting but they have the correct size bush and seal hole for...

Genuine Rover spacer that fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear.

Mini Spares also produce a ring 2 thou thicker 88G549 to...

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)

housing and deleted 1996 on.locking glue used such as locktite

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

USED ONLY-Laygear fitted to gearboxes with 18mm nose on layshaft for fitment with the 17 tooth 1st motion shaft. Basically a 22G927 with larger 13H9513 18mm bearing hole and usually has no identification marks.No warranty

3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc

with tuflock patch to secure.

Used on all mainshafts with 14mm shaft end for the 1st motion shaft---when they went to the 18mm shaft on A plus gearboxes they used DAM7485 which is metric thread.

THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details

Quantity required is 2 per gearbox but the idler gear requires shimming for correct...

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details.

The idler gear in all Mini power units must be set with great care. The thrust wa...

Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts

Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...

Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.

This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...

When you take the side cover off the differential housing on a rod change type gearbox this detent ball sits behind the spring-the spring is 22G2083 and the sleeve is 22G1870. The oil seal for this is 22G1417.

This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.

This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...

Mini Spares Performance Baulk ring.

The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...