£97.49 exc vat
£116.99 inc vat
In stock
£97.49 exc vat
£116.99 inc vat
In stockRecommended usage 1 x 56-9128 to fit one mini.
K&N air filter for 1.5" SU; 5.875" diameter x 1.75" high chrome housing.
K&N developed and manufactures the only air filtration system of it's kind..a high flow, washable filter that's been proven to be the finest in the world. Professi...
For 1.5" carb applications, this Conical K&N filter is the answer. Fits single or dual carb setups. Sold individually.
K & N airfilters are unsurpassed in performance yet are compact in size to fit in even the most cramped quarters. These d...
pair of socks for rampipes on carbs. These should be fitting dry, no oil required.
Round K&N air filter with offset holes to fit ubder the bonnet on minis for HS6 carbs--If you want central holes for other applications see 56-1400
Pancake type filter from K&N which has offset holes giving clearance for fitting to HS2 carbs under a mini bonnet. 47mm deep
Yes, air filter elements should be replaced-about once a year or more often with a lot of rural miles. If your engine runs better without the filter its well past time for a new one. This is the same 37mm high element that fits single HS2
Just what injection engines require, this element will increase the breathing
to the engine which can only result in better performance all round. Once fitted these special elements can last nearly a life time if cleaned and oiled regularly ...
Better flowing replacement air filter for single 1.25" SU and use 2 for twin SU 1.25" carbs. Item sold per filter-one required for single HS2 carb and two for twin carb set up cars. Does not fit mk3 S air boxes as they are shallower.
central fitting for HS2 carbs where there is enough clearance underneath some as Morris 1000 and sprite /midget. Not for mini as there is not enough lower clearance
For 1-1/4" carb applications, this Conical K&N filter is the answer. Fits single or dual carb setups. Sold individually.
K&N airfilters are unsurpassed in performance yet are compact in size to fit in even the most cramped quarters.
Highly polished chrome cover cone filter.
The cotton gauze filter design from K&N provides positive gain that you would expect. Average filter life is 100,000 miles.
'Conical' 5.875" diameter x 2" high, fits 1.75" SU carb.
...
K&N air filter for 1.5" SU; 5.875" diameter x 1.75" high chrome housing.
K&N developed and manufactures the only air filtration system of it's kind..a high flow, washable filter that's been proven to be the finest in the world. Professi...
To get the maximum benefit of K&N filters they should be cleaned periodically.
"Recharger filter care service kit" by K&N; a six step maintenance system to recharge your K&N Filtercharger air filter. Completely restores air flow efficiency ...
Minispares brand Paper element for canister type pre 1974 from the original approved and designated Rover/Unipart source.The more you drive your car, the more frequently you should change your oil. Also check your filter bowl and if it uses oil seal ...
Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014. Original filter for twin point injection cars where it screws directly into the block.
See GFE210 for shorter fil...
Genuine Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014 when parts quality selection changed.
Same manufacturer and item as GFE443 but with our livery on so you know you are g...
Worthwhile fitment on any car and a must for performance engines. This filter has 1/4" ends for standard use, for 5/16" larger bore see PRO805. Supplied as per picture.
universal crank case breather with red top, with a 13mm(1/2")neck size.
2"wide top (50mm) and 35mm high
This combined fuel filter and regulator allows adjustment of fuel pressure for optimum power and fuel economy.The inlet and outlet unions are universal for either 1/4" or 5/16" hoses. The FPR004 is a glass dome version of the alloy bodie...
universal crank case breather with blue top, with a 13mm(1/2")neck size
2"wide top (50mm) and 35mm high.
Universal crank case breather with chrome top and a 13mm(1/2")neck size.
2"wide top (50mm) and 35mm high
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.