£60.00 exc vat
£72.00 inc vat
Out of stock
With pre cast flanges to improve flow and save engine tuners time matching the ports. This is for injection type cars only because it has a sensor hole. The Long Centre Branch des...
£60.00 exc vat
£72.00 inc vat
Out of stock
The newest development in the A-series engine is the use of these nuts with swedged-on washers. The washer will not separate from the nut, so you won't lose it. Yet the nut rotates independently while you tighten it. What a great idea.
Metal gasket for the catalyst and is the same both ends for Cooper 1275CC RSP early cars, but only fitted on the front to later cars. If you cannot fit this gasket on the rear your car does not need one.
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
LONG CENTRE BRANCH EXHAUST MANIFOLD FOR FUEL INJECTED CARS WITH A SENSOR TAKE OFF in main LCB body, THIS IS FOR USE WHEN THE CATALYST IS BEING REMOVED AND A RC40 EXHAUST IS BEING FITTED. If the catalyst is to be retained use [link]C-AEG3...
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
Large bore LCB for competition use or on very large bore street engines; such as 1400cc+. Y-piece outlet end is 2" outside diameter, 1.875"id.
The best quality production exhaust manifold available from Minispares. The Long Center Branch...
LONG CENTRE BRANCH EXHAUST MANIFOLD FOR FUEL INJECTED CARS WITH A SENSOR TAKE OFF in main LCB body, THIS IS FOR USE WHEN THE CATALYST IS BEING REMOVED AND A RC40 EXHAUST IS BEING FITTED. If the catalyst is to be retained use [link]C-AEG3...
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
If you wish to delete the catalyst (legal restrictions apply, so check to see if you are allowed) this pipe is specially made to replace it.
Link pipe for fitting between the LCB and the catalyst. It has a stainless steel knuckle joint to prolong life and give the flexibility required on the system to overcome damage. See also alternative RC40-016
Y piece replacemen...
The newest development in the A-series engine is the use of these nuts with swedged-on washers. The washer will not separate from the nut, so you won't lose it. Yet the nut rotates independently while you tighten it. What a great idea.
Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.
Sold singly,6 per c...
Basically the C-AEG373 LCB exhaust manifold but with a link pipe for retaining the catalyst on carb models after 1990-92.
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
1.75" Bore centre exit twin tail pipe maniflow rear box with adaptor to sleeve down to the standard mini 998cc type exhaust system.
Rear RC-40 twin box system to fit catalyst for cars built late 1991 on SPI(not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a twin box system with a little throatier pleasing note, but a mu...
1.75" bore single box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than our RC40 system. Very high quality with a skid plate on the bottom of the silencer and a polished stainless tip. Suitable for use with an...
Blanking plug to blank of the Lambda sensor hole on all SPI/MPI models.
The famous RC40 Millennium range mild steel twin box exhaust with large bore outlet and side exit plus the fitting kit for the exhaust system.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.