£242.31 exc vat
£290.77 inc vat
In stock
which has a 100 thou jet tube--an alternative to the needle supplied is BDL if other slight modifications or exhaust changes heve been made
Always get your car rolling roaad tested for best ignition/timing and emmissions after fitment.
£242.31 exc vat
£290.77 inc vat
In stockRecommended usage 1 x C-STN18A to fit one mini.
Performance Stage one kit for 1300cc models with HIF44 Carb with centre exit exhaust system RC40-12
Performance Stage one kit for 1300cc models with HIF44 Carb with side exit large bore exhaust system RC40-10
The stock air cleaner housing for many Minis with single 1 1/2" SU carbs have historically been stuck with the paper filter. New from K&N is a replacement element for FZX3013 and all HIF that provides the benefits of K&N cleanable filtra...
Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.
Mini Spares own performance upgrsded paper gasket that sits either side of the carb to manifold spacer on HIF38/44 type 1.75" carbs.Sold singly, order quantity as required to suit your car.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
This plug fits our inlet manifolds and Rover types with servo take off holes..
5/8 UNF grub screw that use 8mm allen key for blanking inlet servo take off or temp transmitter hole at front of pre 1996 cylinder heads. Can also use ADP210
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
If you have fitted our inlet and exhaust manifolds plus an RC40 exhaust to a stadard 1275cc engine this needle in a HIF44 carb will work great if coupled with a K&N pancake filter.
Mini Spares genuine RC40 system has justifiably earned the reputation of the best exhaust ever made for the Mini. Mild steel with stainless steel tailpipe. Typically used with an LCB manifold it gives great performance with a mellow soun...
Performance Stage one kit for 1300cc models with HIF44 Carb with centre exit exhaust system RC40-12
Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
The long wheel base of the Mini Van, Wagon and Pick-up means the popular RC-40 exhaust comes up a little short! This system from Maniflow (pipes, resonator and muffler), is made for the long bodies. It has the same great flow characteristics of the ...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
Better flowing as it has correct shape on every bend and painted grey
The center exhaust hanger takes a lot of abuse during hard acceleration or if you're low enough to bottom out on bumps. This mount has a through metal bolt to keep it intact.
The popular RC-40 exhaust system has been updated for the year 2000. All retain the optimum size 1.75" tubing for maximum performance and efficiency, but we now offer a choice of tailpipe size and configuration. This one is the centre exit 2" outlet ...
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
This short pipe fits on the end of our freeflow manifols C-STR816 to give the overall length of an LCB when you have an exhaust system to fit that was made explicitly for LCB fitment.Total length is 300mm ID is 44mm OD is 48mm.
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
Larger, stronger rear exhaust mounting as used by works cars will usually fit earlier subframes on existing holes in either the middle or side exit position.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Genuine mini Spares inlet manifold dyno tested and designed for our Stage one kit C-STN17. The single SU manifolds is developed to give maximum airflow and gas speed, yet fit all engines even if the standard air cleaner set-up is used. I...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.