£185.00 exc vat
£222.00 inc vat
Out of stock
£185.00 exc vat
£222.00 inc vat
Out of stock
USED laygears--For the late model Mini A Plus gearbox,with single groove identification, this standard ratio laygear was used throughout the range until MPI! No longer available new but we have available good used items in stock where we replace with...
Genuine "A" plus 1st motion shaft, also known as the input shaft.Last few. Fourth gear is the tooth part, this end of the shaft holds the large single roller bearing, with the lower drop gear(input gear) sliding on the outer end of the shaft. 15/21/...
UK MADE third and fourth synchronising hub for all 4 synchromesh mini gearboxes
to the last drawings and specifications
A Plus 2nd gears are marked with a single identification groove.
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and 1st moti...
This is the 1st/2nd gear complete inner and outer hub assembly for all 4 synchromesh gearboxes. 33 teeth outer track
Full rebuild kit with differential parts and standard layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full...
Magnetic drain plug, plus added length to help gather all those metal bits between oil changes. For all manual Mini's.
The metal retainer that holds the rod change gear lever gaiter CZH4278 in place
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
Straight cut teeth broach gear for the 1st motion shaft which runs with the straight cut idler and primary gear combinations. This has 23 teeth and one identification ring on actual teeth.
Achievable drop gear ratios ...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
Full rebuild kit less diferential parts with competition layshaft.
Using only the original manufacturers of the bearings, such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a ...
S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1
24...
Lower differential housing paper gasket for old magic wand and remote type gearboxes, rod change gearboxes.
Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.
Rubber U-joint for yoke-type driveshafts. These are the only new supply available except for QL5000 alternative.
The very early Minis used the rubber U-joint drive couplings to eliminate harshness being transmitted to the passen...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure.Produced in standard material heat treated to the correct core d...
Detent spring in the gearbox on the rod type gearboxes. Some owners have fitted the 22G2083 slightly smaller detent spring which can work but the reverse swicth GAE131 will not function.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.