IDLER GEAR A PLUS STRAIGHT CUT

C-STR30A

£48.38 exc vat

£58.06 inc vat

Out of stock

S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.

Achievable drop gear ratios when using our Evolution gears:

22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1

24...

£48.38 exc vat

£58.06 inc vat

Out of stock

Recommended products

IDLER GEAR SHIM .138/.139" (BLUE)

DAM4825

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See the idler gear in all Mini power units must be set with great care. The thrust washer comes in various thickness to allow for acc...

£16.80 exc vat

£20.16 inc vat

IDLER GEAR SHIM A PLUS SHIM KIT(5 SHIMS)

DAM4821

This kit contains 1 each of 3 alternative sizes plus 2 of the standard size shim

for shimming idler gear on A Plus idler gears. These are the later type spec

which rover superseded to when upgrading the idler gear material on inject...

£78.75 exc vat

£94.50 inc vat

IDLER GEAR SHIM .132/33" A+ (NO COLOUR)

DAM4822

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars.see workshop manual for shimming details.

Quantity required per gearbox is 2 but idler gear requires shimming for correct cle...

£16.80 exc vat

£20.16 inc vat

IDLER GEAR SHIM 134/.135" (YELLOW)

DAM4823

These are the later A+ type spec which rover superseded to when upgrading the idler gear material on injection cars. See workshop manual for shimming details

Quantity required is 2 per gearbox but the idler gear requires shimming for correct...

£16.80 exc vat

£20.16 inc vat

Alternative products

IDLER GEAR WITH ROLLER BEARING CONVERSION A PLUS

C-STR31A

Idler gear conversion for straight cut drop gearsets only.

This set up is for A plus idler gearbox cases only and uses a single roller bearing centrally unlike the old timken conversion which had taper bearings either end.

£125.00 exc vat

£150.00 inc vat

People also bought products

998 24 TOOTH PRIMARY GEAR STRAIGHT CUT

C-STR224

24 tooth primary gear bush for small bore applications, with floating bush

£105.00 exc vat

£126.00 inc vat

998 23 TOOTH PRIMARY GEAR STRAIGHT CUT

C-STR223

S/C 23 tooth primary gear, with floating inner bush

£112.00 exc vat

£134.40 inc vat

INPUT GEAR 25 STRAIGHT CUT

C-STR250

Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.

Achievable drop gear ratios when using our Evolution gears:

22 tooth primary - 30 tooth idler - 25 ...

£40.16 exc vat

£48.19 inc vat

INPUT GEAR 24 TOOTH STRAIGHT CUT

C-STR240

Evolution Straight cut 24 tooth input gear. Usually has 2 identification rings on gear teeth.

Achievable drop gear ratios when using our Evolution gears:

22 tooth primary - 30 tooth idler - 25 too...

£40.16 exc vat

£48.19 inc vat

LAYSHAFT A PLUS PERFORMANCE

C-22A1739

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

£31.85 exc vat

£38.22 inc vat

STRAIGHT CUT 1st GEAR 29 TOOTH

C-22A1735

STRAIGHT CUT 1ST GEAR FOR 4 SYNC SPECIAL TUNING GEARSET.

See table of "Straight Cut Gear Kits" and their components

£54.35 exc vat

£65.22 inc vat

GEAR STRAIGHT CUT A PLUS 1st MOTION SHAFT 19 teeth

C-22A1732A

STRAIGHT CUT FIRST MOTION GEAR FOR A+ GEARSET ORIGINAL ST RATIO

19 teeth

See table of "Straight Cut Gear Kits" and their components

£95.25 exc vat

£114.30 inc vat