£351.75 exc vat
£422.10 inc vat
In stock
Contains 1st motion shaft for larger 18mm mainshaft(A Plus) but with original 22G1040 pre plus laygear which uses a single step layshaft. Can be used on earlier gaerboxes when using the later type larger 18mm end A+ mainshaft. Coverts the original gear ratio to "S" ratio. Gear part numbers are DAM3167 for 1st motion shaft and 22G1040 for laygear. The 1st motion shaft gear was standard fitment on 1275GT from 79-81.
£351.75 exc vat
£422.10 inc vat
In stockRecommended usage 1 x C-AJJ4032A to fit one mini.
18 tooth "S" 1275Gt Ist motion shaft for later A plus layshsft/mainshaft use. Used by competitors who have to use standard gears but wish to upgrade the 14mm end of the mainshaft to the later 18mm type with the larger bearing to give better longevity...
"S" laygear. UK made for all pre-rod change. 4 synchro gears were the same except for the laygear and 1st motion shaft. The Cooper S and 1275GT had a closer ratio with a 18 teeth 1st motion and 29 teeth (15,20,25,29) 22G1040 laygear. The...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...
Straight cut teeth broach gear for the 1st motion shaft which runs with the straight cut idler and primary gear combinations. This has 23 teeth and one identification ring on actual teeth.
Achievable drop gear ratios ...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...
Every 4 synchro gearbox had a straight cut first gear as standard.
This one has 31 teeth and beware complete straight cut race gears sets use a 29 different tooth count.
S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1
24...
Evolution Straight cut 24 tooth input gear. Usually has 2 identification rings on gear teeth.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 too...
Straight cut gearset for A+ gearbox's using the standard 1st and reverse gear. UK made -The ultimate for TUNED street cars or clubman events giving nearly the same close ratios as the original 3 synchro straight cut gear set.
Using latest g...
31 teeth Idler Gear, with one shaft longer than other as per last Rover design modification.If the Mini drive train has a weak link, it's the connection between the engine and the transmission! The idler gear often takes the abuse caused by wear and/...
Input Gear 4-synchro gear.24 teeth
can be used on 3 synchro but the stem part is shorter so you will need to use a spacer by cutting up your old 3 synchro input gear to act as a spacer.
A Plus idler gear-these are the last type made from what they call clean steel to eradicate power train wear and were used on multi points injection cars and work best with Torrington bearings TUK100320-these are priced less than half Rover retail. H...
Grey colour 18 tooth (18.8mm diameter)to go with the 7 tooth Red colour coded larger worm drive spindle TXF10004which is 23mm in diameter-for
SPI overseas 3-2 ratio diff.
BEWARE-there is also another smaller worm 7 to...
This is the gear on the end of the 1st motion shaft that connects with the idler gear. 29 teeth for A plus only-----earlier models had 24 teeth.
MPI Mini /Metro late cars could have 28 teeth with a groove marking-part DAM6337
the ge...
UK MADE third and fourth synchronising hub for all 4 synchromesh mini gearboxes
to the last drawings and specifications
This is the 1st/2nd gear complete inner and outer hub assembly for all 4 synchromesh gearboxes. 33 teeth outer track
High quality version of 13H9513, INA branded.
Dual use bearing fits the end of the A Plus 18mm mainshaft where the 1st Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.
Kno...
Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Full rebuild kit less diferential parts with competition layshaft and EVO baulk rings.
Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use. <...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.