£227.20 exc vat
£272.64 inc vat
In stock
Ist motion shaft to go with this has 18teeth - 22G1371 14mm nose mainshaft or DAM3167 with later type 18mm nose mainshaft.
These have been fitted to Rod change gearboxes with layshaft modifications required when owners required a closer ratio gear set.
£227.20 exc vat
£272.64 inc vat
In stockRecommended usage 1 x 22G1040 to fit one mini.
Pre A plus 4 synchro laygears had 2 of these fitted plus a small bearing whereas the A plus laygear had only one.
With this 18 tooth 1st motion shaft and the 22G1040 laygear these 2 parts made the pre a plus 4 synchro gearbox into a close ratio gearbox as fitted in the 1275GT and Cooper S in standard form.
When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...
4 synchro close ratio helical gear kit for pre A+ gearboxes using an 18mm A+ mainshaft.
Contains 1st motion shaft for larger 18mm mainshaft(A Plus) but with original 22G1040 pre plus laygear which uses a single step layshaft. Ca...
4 synchro close ratio helical gear kit for pre A+ gearboxes using an 18mm A+ mainshaft.
Contains 1st motion shaft for larger 18mm mainshaft(A Plus) but with original 22G1040 pre plus laygear which uses a single step layshaft. Ca...
Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...
Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.
these...
Every 4 synchro gearbox had a straight cut first gear as standard.
This one has 31 teeth and beware complete straight cut race gears sets use a 29 different tooth count.
31 teeth Idler Gear, with one shaft longer than other as per last Rover design modification.If the Mini drive train has a weak link, it's the connection between the engine and the transmission! The idler gear often takes the abuse caused by wear and/...
With this 18 tooth 1st motion shaft and the 22G1040 laygear these 2 parts made the pre a plus 4 synchro gearbox into a close ratio gearbox as fitted in the 1275GT and Cooper S in standard form.
A Plus 2nd gears are marked with a single identification groove.
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and 1st moti...
This is the 1st/2nd gear complete inner and outer hub assembly for all 4 synchromesh gearboxes. 33 teeth outer track
Reverse gear for 3 synchro B type gears. All teeth are straight cut and both rows have 18 teeth.
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips
Short diff housing bolt fitted to Rod change gearbox only 3/8"unc and 2.25"long. For the 2 long STUDS useTAM1617. £0.34 exc vat £0.41 inc vat
For use on Diff housing
Remote type case
53K266 are 4.5" long -4 for remote now use
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc
with tuflock patch to secure.
Remote type gearboxes had four UNC bolts holding the long alloy housing to the differential case. These are the shorter two, 3/8"unc 1"long. The longer two are ZCS628.
Also the bolt to hold the starter motor.
Also the bolt for the [...
Magnetic drain plug, plus added length to help gather all those metal bits between oil changes. For all manual Mini's.
Special height locking type nut for the hardy spicer joints on Cooper S and automatics to fit the 22A1139 bolt. Sorry about the price but only available from Philidas Ltd.
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
Full rebuild kit with diferential parts with competition layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a f...
