£138.75 exc vat
£166.50 inc vat
In stock
£138.75 exc vat
£166.50 inc vat
In stockRecommended usage 1 x 22G1371 to fit one mini.
18 tooth "S" 1275Gt Ist motion shaft for later A plus layshsft/mainshaft use. Used by competitors who have to use standard gears but wish to upgrade the 14mm end of the mainshaft to the later 18mm type with the larger bearing to give better longevity...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...
Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.
these...
Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 ...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...
Every 4 synchro gearbox had a straight cut first gear as standard.
This one has 31 teeth and beware complete straight cut race gears sets use a 29 different tooth count.
"S" laygear. UK made for all pre-rod change. 4 synchro gears were the same except for the laygear and 1st motion shaft. The Cooper S and 1275GT had a closer ratio with a 18 teeth 1st motion and 29 teeth (15,20,25,29) 22G1040 laygear. The...
18 tooth "S" 1275Gt Ist motion shaft for later A plus layshsft/mainshaft use. Used by competitors who have to use standard gears but wish to upgrade the 14mm end of the mainshaft to the later 18mm type with the larger bearing to give better longevity...
17 and 18 teeth rod change rev gear and the 5 speed version-all single bush
UK MADE third and fourth synchronising hub for all 4 synchromesh mini gearboxes
to the last drawings and specifications
A Plus 2nd gears are marked with a single identification groove.
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and 1st moti...
This is the 1st/2nd gear complete inner and outer hub assembly for all 4 synchromesh gearboxes. 33 teeth outer track
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...
Complete bolt kit to bolt the transfer case and clutch cover onto the engine block.
Quick release rod change gear coupling a direct replacement for the standard item, doing away with the troublesome roll pins. It comes complete with high quality quick release clips
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.