£40.16 exc vat
£48.19 inc vat
£40.16 exc vat
£48.19 inc vat
Recommended usage 1 x C-STR230 to fit one mini.
Nut to hold the broach (input) drop gear on the 1st motion shaft and don't forget the DAM4000 locktab. Tiny cut-outs / chamfers go towards the gear as not to dig into the lockwasher as the nut is done up.
Genuine RHP Outer support bearing for the first motion shaft. Comes with bearing and outer race. You MUST REPLACE the outer race when using the new bearing. An easy way to remove the old race is to clean the housing very well, remove the circlip, and...
Evolution Straight cut 24 tooth input gear. Usually has 2 identification rings on gear teeth.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 too...
Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 ...
Idler gear conversion for straight cut drop gearsets only. This set up is for Pre A plus idler gearbox cases only and uses a roller bearing centrally unlike the old timken conversion which had taper bearings either end.
Evolut...
S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current tec...
Straight cut drop gears are the most durable arrangment that can be fitted to a transverse A-series powerunit. These 3 gears are responsible for transferring all the Hp from the motor to the gearbox, so their longevity should be a top priority for an...
Evolution Straight cut 24 tooth 1275 primary gear.
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares h...
Evolution Straight cut 22 tooth 1275 primary gear.
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current technology ...
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares have introduced new EVO straight cut drop gears. With new 2 r...
Idler gear conversion for straight cut drop gearsets only.
This set up is for A plus idler gearbox cases only and uses a single roller bearing centrally unlike the old timken conversion which had taper bearings either end.
Idler gear conversion for straight cut drop gearsets only. This set up is for Pre A plus idler gearbox cases only and uses a roller bearing centrally unlike the old timken conversion which had taper bearings either end.
<...
24 tooth primary gear bush for small bore applications, with floating bush
Evolution Straight cut 25 tooth input/broach gear. Usually has one large marking ring on flange.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 ...
S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 tooth input = 1.136-1
24...
Evolution Straight cut 24 tooth input gear. Usually has 2 identification rings on gear teeth.
Achievable drop gear ratios when using our Evolution gears:
22 tooth primary - 30 tooth idler - 25 too...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
STRAIGHT CUT 1ST GEAR FOR 4 SYNC SPECIAL TUNING GEARSET. £54.35 exc vat £65.22 inc vat
See table of "Straight Cut Gear Kits" and their components
Straight cut laygear for SC/CR 3-sync gearbox.teeth count 13-17-20-23
STRAIGHT CUT FIRST MOTION GEAR FOR A+ GEARSET ORIGINAL ST RATIO £95.25 exc vat £114.30 inc vat
19 teeth
See table of "Straight Cut Gear Kits" and their components
Straight cut reverse gear for rod change box. Has 16 and 18 teeth. £69.90 exc vat £83.88 inc vat
See table of "Straight Cut Gear Kits" and their components
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and result in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correct...