DASH PANEL 2/3 CLOCK OFFSET SPEEDO RHD
DT3047A

£59.42 exc vat

£71.30 inc vat

In stockIn stock
Black vinyl dash liners suitable for 2 and 3 clock clubman type dash with the offset clocks (Right Hand Drive).Vinyl will need cutting out for vent holes but the cardboard backing is pre cut

£59.42 exc vat

£71.30 inc vat

In stockIn stock

Recommended usage 1 x DT3047A to fit one mini.
Headlinings and Trim popular range - Qty 1
Seats and Trim-Mini Saloon MK4-1976-1985 - Mini Cl - Qty 1
Seats and Trim - Mini Clubman Estate 1970-1982 - Qty 1
Seats and Trim - Mini 1275GT - 1969-1980 - Qty 1
Seats and Trim - Mini Non Cooper 1993-96 - Qty 1
Seats and Trim - Mini Cooper 1990-1996 - Pre MPI - Qty 1

People also bought products

The black vinyl covering that lays on your lower dash shelf.for cars after 1970 where the facia panel is not a full metal panel you must fit (link)DT3076(/link)

Fitted for safety regulations to all MK2 minis from 1967-80 except Sweden and Canada to 1975 (not any MKI or van and pick up). Later commercial type minis did have it fitted with 3 clock speedo pod. This is a hard foam pad at the lower edge of the pa...

Pair of black painted type dash cards without airvent holes and for the single speedo only such as van or early saloon. If you have the deluxe type with oil and temp gauge see VGA4192 or in vinyl see ALE2927

Dash liner black painted cardboard without airvents and oval hole for deluxe speedo cluster.Not for single speedo only cluster.For Vinyl leathercloth type see ALE2927

Fresh air vent for the dash, these bolt to the bulkhead and the eyeball socket vents fit into them. These used to be handed but this vent has both hole patterns so will fit both sides. This replaces 37H7035, 37H7036, JJB101000 and JJB101010. Sold ind...

Special clip for the lower brightwork moulding 14A8009 for finishing off the lower dash, crash pad rail, or on earlier cars the painted metal surface of the panel which holds the switch panel section.

The moulding 14A80...

Black vinyl dash liners suitable for 2 and 3 clock clubman type dash with the offset clocks (Left hand Drive).Vinyl will need cutting out for vent holes but the cardboard backing is pre cut.

Printed circuit board for 1989 to 1996 3 clock Nippon Seiko type Mini gauge clusters. These have been unavailable for many years but have now been remade exclusively for Minispares.

Printed circuit board for pre 1989 cars with Smith's type 3 clock gauge clusters. These have been unavailable for many years but have now been remade exclusively for Minispares.

Chromed version of the standard demist vent on early cars where the ashtray is

mounted in the top and middle of the metal facia. Not for later cars with large

padded windscreen rails and ashtray in the front such as Mini Clubman and...

Burr walnut wooden dash for cars with the 3 clock cluster plus 3 extra gauge holes. R/H/D only.

Ashtray that sits in the upper padded dash on all vehicles with 2/3 clocks positioned in front of driver. Early cars had flat plastic tray face whereas later cars had crinkly type face which is the only type available- They all fit the same.

Late type swith carrier with 4 square holes plus heater and choke cable holes-uses the ratchet type choke cable with D shape fitting--earlier cars used round hole for pull and push chooke cableCZH3591

Interior lamp with a black on/off switch and pointed torpedo ends.

Also fitted many of the 1959on range of Austin A55/60 Cambridge, MG Magnette etc.

Also there was an alternative lamp with black switch and square ends 13H192 which w...

Headlining kit for MPI cars, this is grey cloth as apposed to vinyl (much nicer in our opinion). Rear C post panels included.

Our lightweight underfelt kit is the perfect companion when fitting a new headlining. Made from lightweight felt and cut to size, this fits into the cavity of the roof before fitting your new headlining and provides increased sound insulation and pro...

Kit of four plastic carpet protectors for where the seat frame runs. Two are flat and two are shaped to help with the shape of the tunnel. This kit includes the securing rivets. Ideal if your carpet is in good condition but the plastic plates have de...

MK3 Black Mini door and rear quarter trim(4 piece kit) in vinyl as per original twin line pattern per Mini and CooperS but for cars after May 1973 where the rear quarter panel trim shape did not have a cut out for the ash tray mount and if you look a...

Mk1 style alloy gear knob. Will suit any Mini standatd gear lever thread.