1.5" CARB ELBOW GASKET
GUG705559GM

£0.23 exc vat

£0.28 inc vat

In stockIn stock
The paper gasket that goes between the carb and the cleaner elbow or pancake filter on HS4 and HIF38 carbs. For HS2 see 12H862B.

£0.23 exc vat

£0.28 inc vat

In stockIn stock

Recommended usage 1 x GUG705559GM to fit one mini.
Air Cleaner - Qty 1
Air Cleaners - Qty 1

Recommended products

Gasket for an HS4-carb and manifold .Sold seperately and order as required for your car(usually 3).

People also bought products

SU conversion Jet for conerting from a waxstat jet to conventional without having to buy a different linkage etc.

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

Return spring kit for HS4 carburettor spindle.

Metal bracket that fits between the manifold and the HIF44 (1.75")carb to hold the cable - the choke cable clip for this bracket is CZK6491. Also for HIF38. For HS4 carb see 12G766 bracket. Original Turbo type [...

Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housi...

Originally quoted as the HS2 twin carb manifold stud it is one thread longer than CHS2613 which was for single HS2 and spin on oil filter head to the block. UNC course thread for manifold or block and UNF for th...

Twin carb HS2 (1.25")black heatshields with link bar and 3 new return springs.

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orange ...

Clip on the heater valve for heater cables on vehicles from 1990 where the in line remote heater valve was used. It has also been used as a clip for HIF carbs to hold the cable but the one from Rover is 13H3472.

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

Orang...

GASKET BETWEEN CARB AND AIR CLEANER ALLOY ELBOW

Stainless steel twin HS4 heatshields kit. Comes with Link bar and springs.

Throttle return springs for all twin carb variants. Usually 3 fitted.

This is the right hand linkage lever taht sits on the rods between HS type twin carbs. Sold individually

Pair of heatshield brackets and cross bar

these are made similar to the original cooper HS2 design but ARE for HS4 (1.5")carbs and include the 3 correct springs that attach to the bridging bar for choke return linka...

Air ducting tube from inlet manifold to air cleaner. These are 5.5" long which covers the longest but some such as the injection model is only 1.5" OR 2-2.5" long.

Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.

Used in petrol fuel lines to take 1/4" petrol hoses it is used mainly on twin carb set ups for petrol being diverted to the 2 carbs.

This throttle return spring fitted every HS2/4 single SU carb and also on the twins as fitted by the factory. Twin carbs used AEC2075 for choke return. Total length 90mm.