REAR BACK PANEL WITH MK1 LAMP CONVERSION
HMP441046

£310.00 exc vat

£372.00 inc vat

now

£279.00 exc vat

£334.80 inc vat

In stockIn stock
Complete rear back panel section from roof to bumper valance with MK1 lamp and bootlid apertures but the backlight(rear window screen) aperture is only for models from 1967 to 2000. This panel is Not available genuine with the original MK1 size rear window aperture as the pressing is made from the MK2 tooling---If you have a MK1 this is a great repair section which can be cut to suit each individual cars requirements as it is fairly rare for the upper window section to be rotten. An aftermarket panel 14A6484 as per original MK1 is sometimes available.

£310.00 exc vat

£372.00 inc vat

now

£279.00 exc vat

£334.80 inc vat

In stockIn stock

Recommended usage 1 x HMP441046 to fit one mini.
Bodysides and Roof - Qty 1

People also bought products

Rear subframe mounting stiffener L/H repair bracket with holes for subframe mounting and attaches to wheel arch Fits on ALA8623

Rear subframe mounting stiffener panel R/H with holes for subframe mounting to wheel arch. Sits on ALA5524 or ALA5528

Floor pan for Mini van/estate with no x member for remote change gearbox. Non Genuine. For saloon see 14A6491

picture is just to show what you get but bulge on centre tunnel for starter button appears to be on wrong side as this...

MkI aluminium boot lid "skin only" panel. This panel is produced off the original tooling, ensuring good panel fit and integrity. Following the pressing of the panel it is hand finished by Heritage craftsmen, to ensure the highest panel quality.

Non genuine rear companion bin for external hinge cars. These are supplied without the ash try mount.

Non genuine rear companion bin for external hinge cars. These are supplied without the ash try mount.

Rear seat belt anchor mounting point as found on later cars. This panel needs to be welded into the C post.

Rear seat belt anchor mounting point as found on later cars. This panel needs to be welded into the C post.

the left hand waist rail that is supplied on a new bodyside from us.

Acts as a stiffener on the inside of the bodyside between the rear seat pan and the B post just under the rear opening side window

this r/h waist rail is alreday fitted to a new bodyside CZH430 .

It acts as a stifener on the inside of the bodyside just below the rear side window for strengthening between rear seat pan and B post

This rear bulkhead panel is the actual panel the rear passengers back rest against where the upright seat squab is positioned. Not always carried in stock but usually available to special order--this is done to the last factory pressing with the loca...

genuine rear lower back panel for MK2/3 on, which goes up as far as lower edge of backlight seal ridge

Genuine L/H rear quarter outer skin from the B post back for 1970 on wind up window door cars only.From below the rear side window down, including the lip that the rear quarter light window seal sits on but does not include the inner stifener waist r...

Right hand panel behind wheel arch with subframe mounting holes and splash guard panel to stop debris being thrown into rear valance-but is also available with rear valance closing panel as ALA5528 R/H and ALA8623 for L/H

Non genuine rear valance closing panel L/H for saloon cars only,

similar to ALA8623 but less closing panel with 2 holes for mounting rear subframe and 14A6610 floor to wheel arch reinforcement.

rear subframe mounting stiffener L/H repair bracket with holes for subframe mounting and attaches to wheel arch Fits on ALA8623

floor pan front to rear for the left hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mul...