BODYSIDE MK III O/S FROM A POST BACK
CZH430

£395.00 exc vat

£474.00 inc vat

now

£335.75 exc vat

£402.90 inc vat

In stockIn stock
floor to roof high and includes the door frame aperture R/H

£395.00 exc vat

£474.00 inc vat

now

£335.75 exc vat

£402.90 inc vat

In stockIn stock

Recommended usage 1 x CZH430 to fit one mini.
Bodysides and Roof - Qty 1

Alternative products
People also bought products

The last type of rod change rib design floor made for the assembly line fits cars from 1997-2000. It has a large rib down the centre of the L/H side.

This floor produced from genuine tools has the crossmember fitted with the sill panels an...

Non genuine rear valance closing panel with subframe mount repair



The rear valance of the Mini is a panel that is very often in need of replacing. While rear end damage can be a good reason, the most often cause is rust. The pane...

Non genuine rear valance closing panel with subframe mount repair



The rear valance of the Mini is a panel that is very often in need of replacing. While rear end damage can be a good reason, the most often cause is rust. The pane...

Bracket on the end of the dash crossmember(x member holds master cylinders) under bonnet right hand side. The x member is AHC36003

Bracket on the end of the dash crossmember (x member holds master cylinders) under bonnet right hand side. The x member is AHC36003

O/S/F wing t for 1996 on cars. THIS WING STILL NEEDS MODIFYING to allow for fitting of Sportspac arches and 13" wheels. After trimming/cutting to size remember to replace or renew the stiffener lip ALR360380

Has the headlamp re...

L/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3

this is a genuine heritage part.

R/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3

this is a genuine heritage part.

Genuine roof assembly panel with ariel hole. 1996 on

Bracket from the centre of the transmission tunnel up to the centre of the back seat pan

The whole front bulk head assembly with bonnet hinges on the lower dash panel, crossmember and toe board with start of rod change floor tunnel,reinforcements for holding steering rack and heater mounting points --made for vehicles from 1990 on with 1...

Complete rear back panel section from roof to bumper valance with MK1 lamp and bootlid apertures but the backlight(rear window screen) aperture is only for models from 1967 to 2000. This panel is Not available genuine with the original MK1 size rear ...

genuine front panel for the mini clubman before 1976 when the subframe was rubber mounted.see AAM1022 for rubber mounted type as fitted from 1976 on.

the front of these panels is the same but the subframe mounting bracket on the...

This inner wing has the grille slats for the radiator cooling. Built into this panel also is the A panel and door stiffener check strap panel attached for ease of fitment and alignment for wind up window type doors 1969-89.

This rear bulkhead panel is the actual panel the rear passengers back rest against where the upright seat squab is positioned. Not always carried in stock but usually available to special order--this is done to the last factory pressing with the loca...

Aftermarket version of the L/H floorpan for 1991 on cars.

This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 199...

A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.

Experience has shown its easier to fit the genuine panel HMP441001 al...

You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...