£143.76 exc vat
£172.51 inc vat
In stock
ONLY use GCL217 coil for ballasted systems (1982 to 1993 998cc) or GCL216 coil for non-ballasted systems DO NOT...
£143.76 exc vat
£172.51 inc vat
In stockRecommended usage 1 x LU142 to fit one mini.
The two best features of the new Ignitor electronic ignition conversion kit are the low price and the fact that it fits entirely inside your stock distributor cap! All previous ignition kits utilized an external black box, not the sort of thing you w...
NEGATIVE EARTH ONLY..Reproduction CONTACTLESS Distributor suitable for modern day fuels for 850 and 998cc pre 1974 with upgraded rotor arm "Negative earth only". A worn out distributor can cost you both performance and economy. Precise spark timing ...
Electronic ignition conversion. For points type distributors, fixed or sliding. Negative earth only. Also, available for earlier 23/25D on Negative earth (LU142) or earlier 23/25D with Positive earth (LU142AP12).
ONLY use GCL217 coil for bal...
NEGATIVE EARTH ONLY..Reproduction CONTACTLESS Distributor suitable for modern day fuels for 850 and 998cc pre 1974 with upgraded rotor arm "Negative earth only". A worn out distributor can cost you both performance and economy. Precise spark timing ...
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
The two best features of the new Ignitor electronic ignition conversion kit are the low price and the fact that it fits entirely inside your stock distributor cap! All previous ignition kits utilized an external black box, not the sort of thing you w...
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 pre programmed advanced curves built in, a must for any mini with a worn distributor. Full instructions are included with the system. For any A series, A Plus engines...
The O ring that actually sits on the distributor drive spindle shaft in the recess provided.
The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...
This "Pigtail" wire is all that carries current through the distributor to the points.Fits 23 and 25d type distributors
Straight rubber connector pipe. The standard vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could a...
Designed to fit the GDC102 side entry distributor cap as a protection against water, made in rubber.
for 23/25D distributor but see [link]47H5250[/link} for resin type upgrade with 3m of wire as opposed to every aftermarket type analysed with only 1.5m of wire.
its worth paying extra for the condenser and rotor arm [link]GRA101]/link]
Fited to Lucas type distributors with 45D body in 1974 until 1990 when electronic type that was held on by 2 screws appeared as oppossed to this clip on this type. If you need a new distributor clip-we have them as GDC136CLIP.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.