£22.40 exc vat
£26.88 inc vat
In stock
£22.40 exc vat
£26.88 inc vat
In stockRecommended usage 1 x NSC100760 to fit one mini.
Victor Reinz/Mahle small bore head gasket for A-series engines.
Gasket fitment. Writing side up.
Stainless steel small battery cable retaining bracket bolted at the front of the engine for pre engaged manual cars approx 1985 onwards.
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
ARP Head stud kit that compromises of;
4 x Long Head Studs
7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)
11 x Multipoint ARP nuts
11 x Heavy Duty Washers
4 x Rocker post studs <...
Also known as the idle air control valve (IACV). Bolts on the side of the injection body housing to control engine idle speed and air flow from cold start up. The blue socket loom cap fits this unit. This is part of MLZ100090. After fitt...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
Parts required to stop timing chain rattle on A plus engine using special anti stretch single row chain 3H2127EVO.Last chance to buy with the plate and pin to hold the tensioner as they are obsolete from Rover.
Fitted to 998/110...
Mini Spares Evolution Lightweight Performance Piston-single piston and rings.
Press fit only. Same design as C-STN103 but different manufacturer
The ultimate in lightweight die cast pistons, available in +.020, +.040 & +.060 sizes,...
Set of 4 ignition leads from the original supplier to Unipart, suitbale for all twin point minis 1997 onwards
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
Upgraded rocker cover gasket made in silicon, cut outs for 11 stud head and ideal when rocker cover is removed on a regular basis.
Rarely you may require longer rocker cover bolts when fitting this so use CAM6823.
Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.
This chain saves all the time and effort requ...
Upgraded rocker cover gasket made in silicon, ideal for race cars etc where the rocker cover is removed on a regular basis. Mini Spares fitted one on their 1380cc engine road car in August 2014 with great results. Rarely you may require longer rocker...
This is the plug that fits on the back of the front indicator lamps (XBD100670) on mpi models.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.