2nd GEAR 3 SYN B TYPE.ALL

22A980

($45.00) £45.00 exc vat

($54.00) £54.00 inc vat

Out of stock

This is the second gear 28 teeth as used on many 3-synchro Mini gearboxes. Introduced during the late 850 production and continued in use thru the "S" gearbox with the 22G1100 laygear. If you are inspecting your old gears be sure to check the engagement teeth, these are the small teeth on the end of the gear that takes all the abuse as you shift gears. While the large dirve teeth are typically very good, it's the engagement teeth that wear out. Also be sure to check the synchro land area of the gear. When you place a new synchro ring on the gear it should NOT bottom out.

($45.00) £45.00 exc vat

($54.00) £54.00 inc vat

Out of stock

B Type 3 Synchro Mesh Gears - Qty 1

People also bought products

PINION "C" SHIM .004"

GUG705646GM

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

($0.79) £0.79 exc vat

($0.95) £0.95 inc vat

PRE A+ 1ST MOTION NEEDLE ROLLER.

CHM172

This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.

This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...

($3.75) £3.75 exc vat

($4.50) £4.50 inc vat

DIFFERENTIAL ROLLER RHP manufacture

AHU1856

Genuine RHP as originally fitted to every production Mini.

Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.

Some original fi...

($28.29) £28.29 exc vat

($33.95) £33.95 inc vat

BRONZE THRUST WASHER FOR PLANET WHEEL PRE A+

2A7062

The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.

($2.22) £2.22 exc vat

($2.66) £2.66 inc vat

IDLER GEAR NEEDLE ROLLER (3 SYNCHRO) GENUINE ORIGI...

88G302

The 25.4mm wide original genuine bearing to take 19.05mm size idler gear shaft and sits in the gearbox case on early 3 synchro types and also in the early type clutch case. There is a cheaper version on the market but for gearbox safety sake we have ...

($6.50) £6.50 exc vat

($7.80) £7.80 inc vat

OUTPUT SHAFT COLLETT

88G493

Only fitted to vehicles with hardy spicer output shafts (Cooper S and autos). Two collets are fitted in the output shaft in the gearbox and located behind the rubber seal 22A1566

($5.75) £5.75 exc vat

($6.90) £6.90 inc vat

BALL BEARING FOR SYNCHRO HUB 3&4 SYNCHRO

BLS107

Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.

($0.45) £0.45 exc vat

($0.54) £0.54 inc vat

DETENT SPRING FOR MAGIC WAND/REMOTE

2A3647

Detent spring in the gearbox on the remote gearboxes. Some owners have fitted the 22G2083 slightly smaller detent spring which can work but the reverse swicth GAE131 will not function.

($1.80) £1.80 exc vat

($2.16) £2.16 inc vat

LAYSHAFT NEEDLE ROLLER (ALL PRE A+)

88G396

When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...

($3.27) £3.27 exc vat

($3.92) £3.92 inc vat

DIFF SHIM 6 THOU

DAM3108

You will need to shim up your diff bearings with these washers as required. See workshop manuals for details. See also DAM3109 & DAM3633.

($0.79) £0.79 exc vat

($0.95) £0.95 inc vat

ROLLER DOUBLE FOR MAINSHAFT IN GEARBOX. RHP GENUIN...

AAU1365

Genuine RHP bearings. Not cheap Imported rubbish as sold under this part number.

This is the workhorse of the Mini gearbox. This double roller bearing supports the shaft where it transmits the power to the wheels. When this bearing goes, the...

($54.14) £54.14 exc vat

($64.97) £64.97 inc vat

CROWNWHEEL BOLT

ATA7043

This is an aftermarket high tensile shouldered bolt that engine and gearbox tuners are using, as the original shape head and high tensile type bolt is no longer available. For holding the crown wheel to the differential housing.

Sold individ...

($2.85) £2.85 exc vat

($3.42) £3.42 inc vat

SPRING FOR GEARLEVER ANTI RATTLE PRE ROD CHANGE

AEG3123

Does your gearshift lever transmits a lot of rattle and noise,

replacing this tiny but significant parts will likely cure it. The kit for the Spridget or Minor consists of the brass plunger (22A84) and spring (AEG3123) The cup (2A3467) unde...

($0.48) £0.48 exc vat

($0.58) £0.58 inc vat

PINION "C" SHIM .002

GUG705645GM

2 thou shims to go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load--these were sold by Unipart as 3 thou but the Rover drawing we...

($0.70) £0.70 exc vat

($0.84) £0.84 inc vat

DIFF SHIM 10 THOU

DAM3109

See also DAM3108.

($0.83) £0.83 exc vat

($1.00) £1.00 inc vat

DIFF CROWNWHEEL LOCKTAB

ATA7385

All differential crownwheels used these locktabs. 3 required and if you need new bolts see ATA7043 (6 of.) All sold singly

($2.05) £2.05 exc vat

($2.46) £2.46 inc vat

DIFFERENTIAL FIBRE THRUST WASHER STANDARD SIZE

BTA101

Genuine Rover are now 48 thou thick which is so tight they can lock up your differential. The originals were .035 thou. These are machined down to be exactly the correct size required but we also stock oversize 43 thou type which are available as [li...

($1.80) £1.80 exc vat

($2.16) £2.16 inc vat

SHAFT FOR REVERSE IDLER