VACUUM PIPE WITH CONNECTORS
37H4229M

($2.50) £2.50 exc vat

($3.00) £3.00 inc vat

In stockIn stock
Thin plastic pipe with rubber connectors either end. This replaces the old metal type which also had a vacuum chamber built into the line, that was made obsolete. This hose is 26"(660mm)long and has 2 rubber ends, one straight and one at a right angl...

($2.50) £2.50 exc vat

($3.00) £3.00 inc vat

In stockIn stock

Recommended usage 1 x 37H4229M to fit one mini.
Emission, Carburettor Fittings and engine controls - Qty 1
Distributors - Qty 1
Power unit electrics Non Injection - Qty 1
Coil, Vacuum Control Pipes, Ignition Cables & Shi - Qty 1

Kit products
SPI TO HIF44 CARB CONVERSION KIT
C-STN23

To convert a standard UK spec Single Point Injection car to HIF44 carb. This kit includes wiring looms,fuel tank,fuel pump, carb, air filter and inlet manifold.

($1,424.57) £1.424.57 exc vat

($1,709.48) £1.709.48 inc vat
People also bought products
ROCKER COVER GROMMET IN SILICONE
12A1358EVO

High quality silicone version of 12A1358. Fits all A series and A+ rocker covers.

($0.83) £0.83 exc vat

($1.00) £1.00 inc vat
SPINDLE ADJUSTER KIT FOR MPI MODELS
PQL100090KIT

The original adjuster bolt is very expensive, this kit has been made in stainless steel for longevity and includes all 3 parts for adjusting the fanbelt tension on mpi cars at a fraction of the price of the OEM setup.

($30.00) £30.00 exc vat

($36.00) £36.00 inc vat
DISTRIBUTOR HOLE BLANKING PLUG PRE A+
DIZZYPLUG01

Lightweight billet aluminium distributor hole blanking plug for pre A+ engines

($15.00) £15.00 exc vat

($18.00) £18.00 inc vat
DISTRIBUTOR HOLE BLANKING PLUG A+
DIZZYPLUG02

Lightweight billet aluminium distributor hole blanking plug for A+ engines.

($17.50) £17.50 exc vat

($21.00) £21.00 inc vat
SPIN ON OIL FILTER CONVERSION KIT
TAM2097FK

A kit to convert the early style cartridge oil filter to the later style spin on filter.

($20.11) £20.11 exc vat

($24.13) £24.13 inc vat
VICTOR REINZ LARGE BORE HEAD GASKET
GUG702560VR

Victor Reinz large bore head gasket for A-series engines.

($13.50) £13.50 exc vat

($16.20) £16.20 inc vat
RAMAIR HS4/H4/HIF38 1.5" AIR FILTER
RS2-201-401

Ramair’s hugely successful range of filter kits, designed to bolt directly to the carburettor body, is used widely in both competition and street applications. The element is of sturdy construction, supported by a stainless steel cage and provides ma...

($48.11) £48.11 exc vat

($57.73) £57.73 inc vat
ENGINE MOUNT BOLT KIT FOR ALL MANUAL TYPES
21A1902FK

Engine mount bolt kit for manual cars, 1 kit requried per car.

($3.83) £3.83 exc vat

($4.60) £4.60 inc vat
CRANK THRUST WASHER SET STANDARD 998
ACL2122

Set of standard size 998 thrust washers.

($9.75) £9.75 exc vat

($11.70) £11.70 inc vat
VICTOR REINZ SMALL BORE HEAD GASKET
GUG702506VR

Victor Reinz/Mahle small bore head gasket for A-series engines.



Gasket fitment. Writing side up.

($10.40) £10.40 exc vat

($12.48) £12.48 inc vat
ROLLER ROCKER SPACER KIT FOR RACE ALLOY 5 PORT
C-AEG393

($12.00) £12.00 exc vat

($14.40) £14.40 inc vat
ACL SMALL BORE ENGINE CAM LINER SET
ACL3046

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

($16.14) £16.14 exc vat

($19.37) £19.37 inc vat
VALVE SPRING SEATS SHIMS 0.020"(set of 4)
SS1

Spring seat shims (set of 4), 0.020" thick (0.5mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...

($6.90) £6.90 exc vat

($8.28) £8.28 inc vat
TIMING COVER AND FRONT PLATE FITTING KIT
MSSK063

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

($8.00) £8.00 exc vat

($9.60) £9.60 inc vat
11/16" DOWTY SEAL
DSM18

11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102

($2.40) £2.40 exc vat

($2.88) £2.88 inc vat
PUROLATER FILTER BOWL TO HEAD SEAL
12A1591

This is the large seal for the early type oil filter assembly pre spin on type.

($3.00) £3.00 exc vat

($3.60) £3.60 inc vat
OXYGEN SENSOR LAMBDA UNIT (SPi & MPi) BOSCH
MHK10004BOSCH

Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.

($78.57) £78.57 exc vat

($94.28) £94.28 inc vat
CYLINDER HEAD HEATER TAP FITTING KIT
ADU9102FK

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

($1.60) £1.60 exc vat

($1.92) £1.92 inc vat
SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275 +40
C-STN103-40

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

($299.00) £299.00 exc vat

($358.80) £358.80 inc vat
SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275 +20
C-STN103-20

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.

Glyn Swif...

($299.00) £299.00 exc vat

($358.80) £358.80 inc vat