($0.83) £0.83 exc vat
($1.00) £1.00 inc vat
In stock
This is also the bolt that goes through the dowel on the engine block to transmission case and is used on gearbox cases.
GFK5170 is 1.5" long
BH604131 is 1.6250"
BH604141 is 1.75"
($0.83) £0.83 exc vat
($1.00) £1.00 inc vat
In stockRecommended usage 3 x BH604141 to fit one mini.
Universal paper oil pump gasket for all A series engines. Fits between pump and block. See GUG705560GM for genuine.
Until the Verto/injection type cars most minis had a small inspection hole for checking timing at the top of the clutch housing. These 1/4"unf bolts 1/2" long hold on that plate but you can use shorter type SH604031 also.
Also ...
Complete nut, bolt and washer set for engine to gearbox only
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
Complete nut, bolt and washer set for engine to gearbox only
Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.
Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.
Solid dowel at the front of the engine that locates the block to gearbox.
later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable
3/8"unc 1"long
A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...
Longer main bolt stud.
As supplied with our main strap kit.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
You require 5 of these high tensile short head studs and they torque to 42lb/ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud [link]C...
Original short pin drive oil pump for all Pre A Plus minis with 850/998/1100cc engines except autos and others with star drive or the later slot drive pumps as found on A Plus blocks.
Competition Slot drive pump for 1300cc A-Plus engines.
Almost all oil pumps available today have the same design capacity. The problem is the lack of precise manufacturing. Most factories in their quest for production volume have sacrificed ...
Special "S" main bearings nut set (6).7/16"AF thread
On all performance A series engines it is essential to ensure accurate and as near permanent location of the centre main bearing of the crankshaft as possible. Flexing allowed here, especi...
Slot drive pump for 998cc A-Plus engines.
All oil pumps are not created equal! Almost all pumps available today have the same design capacity. The problem is the lack of precise manufacturing. Most factories in their quest for production vol...
Special bolt that fits the engine front plate to support the adjusting link for alternators/dynamo
The special washer under the tappet cover bolt.Sold singly 2 required per engine.
See 12A1176 for seal
Steel center main strap for small bore engines, comes with longer high tensile bolts. The Main bearing top cap will need machining flat, no other modifications required. Engine bolt hole centres all slightly vary from 2.775" to 2.785" - some 0.010" o...
The oil pump with a difference. This pump was designed as a long lasting modern oil pump. The steel backing provides rigidity and improved life expectancy. The two bolt design allows the use of this pump in any block configuration. The drive required...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.