($29.12) £29.12 exc vat
($34.94) £34.94 inc vat
In stock
($29.12) £29.12 exc vat
($34.94) £34.94 inc vat
In stockRecommended usage 1 x C-22A1738 to fit one mini.
Pre A plus 4 synchro laygears had 2 of these fitted plus a small bearing whereas the A plus laygear had only one.
When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...
Full rebuild kit less diferential parts with competition layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a f...
Full rebuild kit with diferential parts with competition layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a f...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Full rebuild kit less diferential parts.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full kit of bearings except...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure.Produced in standard material heat treated to the correct core d...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material EN36 and heat treated to the c...
Shaft that reverse gear sits on in rod change type gearboxes.
Genuine Rover Tuftrided diff pin, as fiited to all the later A+ gearboxes as a standard upgrade. These are the last genuine parts left and will not be available again
IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...
S/C 30 tooth idler gear for A+ boxes using the 7/8" shaft.
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current tec...
Evolution Straight cut 24 tooth input gear.
These gears are banded with 2 rings for identification.
Do not mix and match with other gears that have same teeth counts unless they have the same 2 identification bands
...
Straight cut teeth broach gear for the 1st motion shaft which runs with the straight cut idler and primary gear combinations. This has 23 teeth and one identification ring on actual teeth.
Achievable drop gear ratios ...
Evolution Straight cut 24 tooth 1275 primary gear.
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares h...
Evolution Straight cut 23 tooth 1275 primary gear.
Ongoing development and investment of bringing parts up to date from yesturyear with current technology Mini Spares have introduced new EVO straight cut drop gears. With new 2 r...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)
housing and deleted 1996 on.locking glue used such as locktite
24 tooth primary gear bush for small bore applications, with floating bush
Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine RHP/NSK bearings
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.