($11.25) £11.25 exc vat
($13.50) £13.50 inc vat
($11.25) £11.25 exc vat
($13.50) £13.50 inc vat
Recommended usage 2 x GRK2076 to fit one mini.
Master Cylinder repair kit for repairing the late GMC90376 master cylinder that was attached to the servo from 1995 until the end of production this kit uses a longer seal in conjunction with a nylon bearing. If your master cylinder has a drill hole ...
NOTE: DOES NOT COME WITH THE SWITCH - HAS A BLANKING BOLT FITTED
The last diagonal brake split models had this square plastic canister (reservoir). With metric unions it's recognised by the rectangular reservoir and small cap with ...
Original AP Lockheed type metal body master cylinder.
Fitted with a plastic cap the metal original alternative is available seperately as 17H5323
Ensure the correct DOT4 or DOT5.1 brake fluid is used as these cylinders...
Almost every Mini built prior to the dual circuit system uses a .70" bore master cylinder. This kit fits them all. The original size in the '59-'64 Mini was .75" but as most of these cylinders have been replaced with the .70" size it is best to check...
Genuine AP Master cylinder with plastic tank.
The master cylinder is the heart of any hydraulic system and the hardest to troubleshoot. A pedal that can be slowly pushed to the floor indicates the master cylinder is worn. Fluid dripping off ...
Genuine AP Lockheed boxed - Made in UK - fitted from 1988 on, this master cylinder uses a built in servo.
This master cylinder was used right up to the last production twin point vehicles from Rover. Bore size is 20.6mm(.811").
See ...
Genuine AP Lockheed boxed and made in UK. FRONT TO REAR master is the latest model dual master cylinders, which was introduced in 1985 with a stepped bore of 17.8 to 19mm to replace any previous master cylinders from September 1978 to 1988 when the b...
These repair kits are for the early twin leading front drum brakes wheel cylinders GWC102/3 with .8125" bore size. The later twin cylinder set up used .9375" size part number GRK2002.
Please note however - if your cylinders are...
If your wheel cylinder does not bolt on it uses this special clip. Some new wheel cylinders come with this clip included so check on ordering.
5/8" bore-Fitted to all Cooper 'S' hydrolastic cars from Sept 1964 plus mini to 1967.Also used from 1959-1963 and intermittently on. Leyland used this smaller type cylinder with servo on disc set ups as standard.
Bleed nipple now 7mm spanner...
Non genuine 0.625-5/8" reproduction rear wheel cylinder used from 1959-1967.
Quantity one per rear wheel and 2 required for car set.
Bleed nipple now 7mm spanner size but same thread-original 513118A used to be 6.2mm (1...
Twin leading shoe brakes use two wheel cylinders per wheel, but you buy them singly. These cylinders are the 15/16" diameter style that will fit MK1/2/3 models 1964 on with .9375" bore size with 1 1/2" shoes.
Sold with bleed nipple but requi...
This master cylinder had a larger capacity fluid bowl 3" high and was fitted to all cooper S and 1275GT with single line brakes. Will also fit standard single line mini if you are looking for larger capacity fluid reservoir especially when using cali...
Twin leading shoe brakes use two wheel cylinders per wheel, but you buy them singly. These cylinders are the 15/16" (.9375") diameter style that will fit MK1/2/3 models 1964 on with 1 1/2" shoes.
Sold with bleed nipple but require[link]37H38...
Genuine original AP lockheed L/H front wheel cylinder for twin leading shoe drum brakes for cars from 1964. Bleed nipple included and37H3833 gasket. These are 0.9375" bore size which is larger than the MK1 type and the repair kit is [lin...
Wheel cylinder rebuild kit for GWC1102. 75' rear wheel cylinder.
Sold individually per cylinder
Extension piece in translucent white plastic screws on metal canister type master cylinders only. The seal provided slips over the thread of the filler neck and sits on the tank for the extension piece to screw down onto and seal. The original cap fi...