STUD FOR SCREW ON OIL FILTER PLUS HS2 CARB

3/8"unc 1.6250" long stud for engine block to accept the TAM2097 screw on filter head and for HS2 carbs, alternative to this is CHS2614 1.75" long and just over one thread longer. LYG10008 bolt was ...

($1.68) £1.68 exc vat

($2.02) £2.02 inc vat

OIL FILTER HOUSING - PRE 1992

TAM2097

Filter housing for spin-on filter.

This housing uses a 1/4 npt taper thread union.

The later type (92onwards) 12A engine numbers has 11/16" thread size.

For performance use see 12A2032RACE.

($12.80) £12.80 exc vat

($15.36) £15.36 inc vat

GASKET OIL FILTER HEAD LATE GENUINE

GUG705553GM

Block to filter head gasket when spin on type filter is used (except billet types which use 88G402). The black side goes against the engine and the red against the filter. This also has a sealant strip on it to help stop leaks.

($1.74) £1.74 exc vat

($2.09) £2.09 inc vat

SPRING WASHER 3/8"

GFK1126

($0.12) £0.12 exc vat

($0.14) £0.14 inc vat

NUT PLAIN 3/8" UNF

GFK3213

($0.11) £0.11 exc vat

($0.13) £0.13 inc vat

OIL FILTER SPIN ON 1973-1996 not MPI

MSF166

Genuine Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014 when parts quality selection changed.

Same manufacturer and item as GFE443 but with our livery on so you know you are g...

($3.30) £3.30 exc vat

($3.96) £3.96 inc vat

OIL FILTER REPLACEMENT ELEMENT PRE 1974

MSF103

Minispares brand Paper element for canister type pre 1974 from the original approved and designated Rover/Unipart source.The more you drive your car, the more frequently you should change your oil. Also check your filter bowl and if it uses oil seal ...

($5.39) £5.39 exc vat

($6.47) £6.47 inc vat

OIL FILTER MPI SPIN ON-(FITS TO BLOCK ONLY)

MSF280

Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014. Original filter for twin point injection cars where it screws directly into the block.

See GFE210 for shorter fil...

($3.76) £3.76 exc vat

($4.51) £4.51 inc vat

OIL FILTER SPIN ON 1973-1996 not MPI

MSF166

Genuine Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014 when parts quality selection changed.

Same manufacturer and item as GFE443 but with our livery on so you know you are g...

($3.30) £3.30 exc vat

($3.96) £3.96 inc vat

OIL FILTER FOR MPI WHEN RUNNING AN OIL COOLER KIT

GFE210

Short oil filter for MPI when space is restricted through modification or optional oil cooler fitted

MANN supplied Filter

this short filter DOES NOT fit the MPI block. it ONLY fits the oil cooler take off

($9.68) £9.68 exc vat

($11.62) £11.62 inc vat

MILLERS ENGINE FLUSH - 250ML

MILLERS005

Engine flush removes sludge and other unwanted deposits from oil galleries before new clean oil is added meaning the oil stays cleaner between changes. One bottle treats 4-6 litres of oil.

($4.96) £4.96 exc vat

($5.95) £5.95 inc vat

CLASSIC CASTROL PINT METAL POURING JUG

J105

Classic Castrol Metal pouring jug, 1 pint.

($10.66) £10.66 exc vat

($12.79) £12.79 inc vat

TOOL09 WRENCH + MSF166 OIL FILTER

GS102440

Tool to remove the oil filter and a genuine spin on Mini Spares filter pre MPI cars, as sold by Rover and Unipart but in our livery until their closure.

($29.03) £29.03 exc vat

($34.84) £34.84 inc vat

OIL FILTER MSF166 AND OIL MILLERS001 SPECIAL OFFER

SO1

One spin on filter and Genuine Millers Mini 20W50 oil

($28.06) £28.06 exc vat

($33.67) £33.67 inc vat

MINISPARES OIL PLUS MSF166 OIL FILTER

SO4

Minispares own 5 litres of 20W50 mineral oil, see GUL7005T plus a spin on oil filter pre 1996 from the original supplier to Rover/Unipart, see MSF166

($24.72) £24.72 exc vat

($29.66) £29.66 inc vat

OIL FILLER CAP NON VENTED

12A402

Original rocker cover cap without internal filter==now use 13H2296

($3.25) £3.25 exc vat

($3.90) £3.90 inc vat

MULTIGRADE CLASSIC OIL 20W50 5LTR

GUL7005T

Mini Spares produced 20w50 mineral oil-everbody loves this great value oil

Mini Spares own branded oil with a high amount of Zinc/ZDDP (1300ppm) compared to Castrol equivalent 800PPM- this oil is as close as we could get to the oil...

($22.08) £22.08 exc vat

($26.50) £26.50 inc vat

VICTOR REINZ LARGE BORE HEAD GASKET

GUG702560VR

Victor Reinz large bore head gasket for A-series engines.

($13.50) £13.50 exc vat

($16.20) £16.20 inc vat

RAMAIR HS4/H4/HIF38 1.5" AIR FILTER

RS2-201-401

Ramair’s hugely successful range of filter kits, designed to bolt directly to the carburettor body, is used widely in both competition and street applications. The element is of sturdy construction, supported by a stainless steel cage and provides ma...

($48.11) £48.11 exc vat

($57.73) £57.73 inc vat

ENGINE MOUNT BOLT KIT FOR ALL MANUAL TYPES

21A1902FK

Engine mount bolt kit for manual cars, 1 kit requried per car.

($3.83) £3.83 exc vat

($4.60) £4.60 inc vat

CRANK THRUST WASHER SET STANDARD 998

ACL2122

Set of standard size 998 thrust washers.

($9.75) £9.75 exc vat

($11.70) £11.70 inc vat

VICTOR REINZ SMALL BORE HEAD GASKET

GUG702506VR

Victor Reinz/Mahle small bore head gasket for A-series engines.

Gasket fitment. Writing side up.

($10.40) £10.40 exc vat

($12.48) £12.48 inc vat

AC DODD ROAD TORQUE CAMSHAFT

ACD-RT

AC Dodd Road Torque cam, great for low end power. Please see picture for full cam specs.

Road torque, this cam for strong low & mid range lugging, Touring, Smooth idle, excellent emmisions

ACD - RT

Power...

($214.40) £214.40 exc vat

($257.28) £257.28 inc vat

ACL SMALL BORE ENGINE CAM LINER SET

ACL3046

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

($16.14) £16.14 exc vat

($19.37) £19.37 inc vat

TIMING COVER AND FRONT PLATE FITTING KIT

MSSK063

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

($8.00) £8.00 exc vat

($9.60) £9.60 inc vat

CYLINDER HEAD HEATER TAP FITTING KIT

ADU9102FK

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

($1.60) £1.60 exc vat

($1.92) £1.92 inc vat