(0,68 €) £0.68 exc vat
(0,82 €) £0.82 inc vat
In stock
(0,68 €) £0.68 exc vat
(0,82 €) £0.82 inc vat
In stockRecommended usage 2 x AUC1152 to fit one mini.
If fuel is overflowing the float bowl the needle valve is leaking. This may be caused by the float WZX13040(GSU200) being misadjusted, stuck or leaking OR the needle may be fouled with a bit of grit or worn and not sealing. This is an
altern...
Paper gasket for the float bowl of any HS2/HS4/HS6 carbs.
HS2 float lid assy, also fits HS4.
A rare chance to do something the easy way and at the same time do it right. A new plastic float, pin, plus needle & seat assembly are already installed into a new float cover lid. Simply remov...
The new adjustable height StayUp® Float is resistant to modern ethanol based Fuels and has a military spec closed cell construction making it puncture proof. The ability to adjust the Float Arm allows for quick and easy minor alterations to Float lev...
Fitted to HIF38 and HIF44 carbs, ethanol tolerant product. Bigger bodied valve.
For turbo models see WZX1095 .Quantity required-1
spindle and fixings only for the HS2 carb-the butterfly for this is WZX1320.
sorry folks but buying both kits you get double the gaskets
This is the original type of needle valve that governs the plastic fuel float in your SU carb.
An alternative better upgraded version is available as CA90.
The metal washer AUD2193 goes up against this seal on the jet where it enters the float bowl on all HS type carbs.
Complete with screw the choke trunnion is used on nearly all SU carb linkages.
See ACC5062 for carb cable link trunnion also.
Early single HS" carbs had these splendid looking brass top dashpot dampers which are interchangeable with the plastic type.
These screws fit all HS type carb butterflies to hold them on the throttle spindle
Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS2 carbs. As a guidline 0.250" internal diameter and ream carb bo...
Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the L/H ( front) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds- Midgets and MGB used different angles,u...
Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...
Float grommet for the mini twin HS2/4 carbs---this 30 degree angle is for the R/H ( rear) carb and is positioned to angle the float bowl--Used on both twin HS2/4 carbswhen using correct mini inlet manifolds-Midgets and MGB used different angles,usual...
Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS4 carbs. As a guideline 0.3125" internal diameter ream body to 9...
Paper gasket for the float bowl of any HS2/HS4/HS6 carbs.
If fuel is overflowing the float bowl the needle valve is leaking. This may be caused by the float WZX13040(GSU200) being misadjusted, stuck or leaking OR the needle may be fouled with a bit of grit or worn and not sealing. This is an
altern...
Clip for holding the choke cable on the HS carb abutment bracket 12G766.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.