(0,28 €) £0.28 exc vat
(0,34 €) £0.34 inc vat
In stock
The original metal type are prone to rust so Mini spares producedd these stainless steel versions which are also cheaper. Supplied as a single clip, order as many as ...
(0,28 €) £0.28 exc vat
(0,34 €) £0.34 inc vat
In stockRecommended usage 28 x BMP128MS to fit one mini.
Zinc plated mild steel clip for fixing vertical seam mouldings to the body.
These are the original Rover Xparts clips that hold on the vertical seam mouldings for all minis, prone to rust this was Rovers upgrade but Mini spares produced a stainless steel version BMP128MS which is also cheaper and a better option...
Upper door moulding rivet for Cooper S door trim. For Mk1 usually 1 at front and 3 at back making 4 per side and on Mk2 there were 2 per end at bottom making 4 per side. This is the 10mm head rivet and not required on our own 14A9773/9774 trims that ...
Curley carbon fibre Mini Miglia wheel arches, approximately 4.8." wide, with front edge 6.9" at widest point. Requires MS127FK brackets. Probably the largest wheel arches used on minis. Set of 4.
Complete fitting kit as supplied with most Tex mirrors.
Wiper mounting kit for Mk1 Mini's (3 required per car). Each kit comes with a pin, nut, 2 washers and mounting rubber.
Wheel arch fitting kit for MS127 Mini Miglia arches.
Group 2 fibre glass wheel arches in premium black finish not requiring paint, judged the best on the market available by our customers, they stick out 1.75" including lip, when bodylines (wheel arch and moulding lip) are kept original. Screws are vis...
Original shape washer jet for Mk1/2 minis. Made to the same specification as the last type made for rover parts sales with a nut on a loose thread so it can be tightened easily by hand in the engine bay without any modifications. Should be used with ...
Clip under front floor fitted to 1990 for holding fuel/ brake lines (2 per car)
located beside floor pan footwell and tunnel
Clip for underside of front floor(3 per side) 6 in total fitted to 90
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.
3.3mm thick from the tanneries for use on horse bridles,wit...
Roof gutter trim clip in stainless steel, ideal finishing item for our MT632 roof gutter trim.
Minispares 2 piece plastic roof moulding kit specially shaped for the corners and drain holes as fitted from 1980on in black.
The 2 joining and finishing clips are DBE10006PMD which need to be ordered seperately. The last Rover...
Original MK1/2 shape Windscreen washer cycle type bottle clip, about 1964 on.
Has yours disappeared, or just disintegrated with age?
The original winguard MK1 bottle part number was ADA3833 NOW 17H2536 for MK1/2.
<...
This is the small plastic nut used to hold the fuel line protector shield on later cars, also used to hold the catalytic converter heat shield on, 4 required for each shield.
Fixing stud for latest new type genuine Sportspack arches. (Five required per arch)
Original MK1/2 shape with correct 1.25" small neck.
Originally made by Winguard these plastic washer bottles for early Minis were often asked for but rarely available.
The original part number for the Winguard MK1 bottle was ADA383...
The scrivet for holding the front of the rear wheel Sportspack arch and the rear of the front arch. Rover also used rivet RY612535 as an alternative.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.