(255,03 €) £255.03 exc vat
(306,04 €) £306.04 inc vat
(255,03 €) £255.03 exc vat
(306,04 €) £306.04 inc vat
The stock air cleaner housing for many Minis with single 1 1/2" SU carbs have historically been stuck with the paper filter. New from K&N is a replacement element for FZX3013 and all HIF that provides the benefits of K&N cleanable filtra...
Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.
Gasket for an HS4-carb and manifold .Sold seperately and order as required for your car(usually 3).
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
The favourite and best needle for Minispares stage one kit. Tested on a rolling road by Peter Baldwin this baby gave the best performance when using our RC40 system, Minispares inlet and exhaust manifold plus a K&N filter.
If us...
This plug fits our inlet manifolds and Rover types with servo take off holes..
5/8 UNF grub screw that use 8mm allen key for blanking inlet servo take off or temp transmitter hole at front of pre 1996 cylinder heads. Can also use ADP210
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...
STAGE 1 KIT. Mini Spares bolt-on performance kit for 998 and 1098 engines with HS4 carb. Gives 20% more power and 12% more torque.
Using all the top quality tried and tested parts the Kit includes
RC40 twin box [link]RC...
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.
Original side exit RC40 Std bore exhaust, freeflow long downpipe and fitting kit.
This includes the long downpipe for use with the freeflow type manifold. Can be cut for LCB use or see RC40PACKAGE001.
Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...
Middle exhaust mounting, bolts on to the front of the rear subframe and is the central or first of the rubber mountings. see GEX7081POLY for Poly type or if you are fed up with breakages see C-19G3257.The original Genuine pa...
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s and for street 1380s.
There is NOT enough clearance room when fitting to old cars with rubber couplings which foul. Using [lin...
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.
Exhaust mounting kit includes the 2 hanging brackets and 2 rubber mountings, manifold clamp and fixing nut/bolts for installing an original standard 850/998cc saloon exhaust. To mount an RC-40 exhaust system see RC-40FK.
The popular RC-40 exhaust system has been updated for the year 2000. All retain the optimum size 1.75" tubing for maximum performance and efficiency, but we now offer a choice of tailpipe size and configuraton. In addition they now have stainless ste...