(3 627,75 €) £3 627.75 exc vat
(4 353,30 €) £4 353.30 inc vat
Special order
Ratios are:
1s...
(3 627,75 €) £3 627.75 exc vat
(4 353,30 €) £4 353.30 inc vat
Special orderRecommended usage 1 x MSG03-31 to fit one mini.
Special locking washer for 3rd gear on 4 synchro gearboxes plus our own 5 speed 5th gear. The washer for 2nd gear is 22G839
Only for the 4 synchromesh gearbox synchroniser gear hub. There are 3 of these per hub with BLS107 ball bearing.
Minispares recommend this central oil pick-up be installed with every transmission rebuild.
The original Mini oil pick-up pipe lives in the right hand edge of the gearbox casing, which is okay if you are driving straight. But during a right ...
The favourite final drive for minis this is the pre A plus type which was stronger and fitted to Cooper S etc. goes with 22A411 crownwheel.
The longer one piece bush as fitted to all late reverse gears. Early type had 2 single bushes which sometimes came adrift after arduous use.
All differential crownwheels used these locktabs. 3 required and if you need new bolts see ATA7043 (6 of.) All sold singly
Genuine RHP bearings. Not cheap Imported rubbish as sold under this part number.
This is the workhorse of the Mini gearbox. This double roller bearing supports the shaft where it transmits the power to the wheels. When this bearing goes, the...
Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Upgraded version in Viton available us ADU5738VITON
This is the original Evolution"Cross-pin" differential for the Mini.
Produced and sold by Mini Spares since 1994. It is a super heavy duty differential designed as a significant upgrade for reliability and strength to the standard units. Ove...
Try these GENUINE MINISPARES superseal gearbox output shaft gaskets specially made to try and eliminate leaks.
Sold singly,2 per gearbox
Torrington/Koyo idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior...
Often overlooked when doing gearbox rebuilds this seal is very important as it sits in the very bottom of the case and is the source of irritating oil leaks.
The large round metal plug in the bottom of the gearbox is the pivot pin for all th...
for the inspection plate on the front cover of the transmission where the speed cable goes to -it has 2 bolt holes cut out
Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.
Gearbox oil strainer to gearbox internal case gasket and also used on the C-AHT54 special oil pick up pipe. One also sits on the outer plate held onto the gearbox outer casing by 2 screws.
Lower differential housing paper gasket for old magic wand and remote type gearboxes, rod change gearboxes.
Every 4 synchro gearbox had a straight cut first gear as standard.
This one has 31 teeth and beware complete straight cut race gears sets use a 29 different tooth count.
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.