£1.25 exc vat
£1.50 inc vat
£1.25 exc vat
£1.50 inc vat
Recommended usage 4 x 37H3043 to fit one mini.
THIS IS THE SMALL DOOR HINGE GASKET ON THE A PANEL FOR SLIDING WINDOW TYPE DOORS.
THIS IS THE LARGE GASKET THAT FITS BEHIND THE HINGE ON THE DOOR OF AN EXTERNAL
HINGE ON CARS WITH SLIDING WINDOWS SUCH AS MK1/2. SEE BMP135 FOR SMALL ONE.
It is possible and almost easy to repair sagging Mkl Mini door hinges . You don't even have to remove the hinges from the car. Once you have removed the original hinge pin you simply drill a hole in the front hinge half, push in the bush and reassemb...
basically a centre punch but this is the correct size and made for getting the pin out of external mk1/2 door hinge
Small kit to help the removal of the usualy difficult to move brass bush in the external hinges (MK1/2/VAN/PICKUP)
This kit contains one pin and one bush for repairing the external hinges on MK1/2 doors. If they are badly worn and you need Hinges see 14A6818/19/20/21.
If you require a new set of studs see 14A6818BOLT a complete car set in st...
This kit contains one pin and one bush for repairing the external hinges on MK1/2 doors. If they are badly worn and you need Hinges see 14A6818/19/20/21.
If you require a new set of studs see 14A6818BOLT a complete car set in st...
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.
Regre...
The rubber that sits in the frame to hold the windows on wind up window type doors. The frames are ALA5746/7 or see MSSK2105 also used on Clubman Estate and Traveller rear windows in the finger pull grips.
Sold individually.2 pe...
Sliding window type weatherstrip kit R/H
kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...
Sponge type seal on L/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust.
Sponge type seal on R/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust, if the sponge is gettig hard then replace it.
Moulded shape type right hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9.
Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the R/H upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.
Genuine MK3 wind-up window upper slide up and down felt lined channel that fits into the upper door frame. Left (PAM3077) and right (PAM3076) look identical but are mirror images.If you are looking for a cheaper budget version see PAM3077MS
...
pair of outer door seal mouldings and fixing clips
These are the original type without the black plastic ends which were introduced on later models for safety criteria. All outside moudings are interchangable but are sided.
Genuine Mini Spares mouldings product as supplied to Rover.
Pair of the later door outer mouldings plus ADH3809 clips to help prevent water running down the windows causing rust.
These have black plastic ends for car s...
Sliding window type weatherstrip kit L/H
kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder
This kit contains one pin and one bush for repairing the external hinges on MK1/2 doors. If they are badly worn and you need Hinges see 14A6818/19/20/21.
If you require a new set of studs see 14A6818BOLT a complete car set in st...
The square/oblong plastic finisher that goes on the door where the safety lock is located on Mk3 1970 on cars with wind up windows. This is the original style which changed on the SPI and then again on the MPI. If you have a SPI or MPI from 1991 on, ...
Moulded shape type left hand door stay grommet fitted until 1985 when it was replaced by a flat sponge type seal CGE10038/9.
Plastic window locks for sliding windows, metal ones are no longer available.
24A1194 = Right Front
24A1195 = Left Front
24A1196 = Right Rear
24A1197 = Left Rear
Sliding window Mini models all must now use these black plastic locks for the windows. Our special kit includes a complete set of all the pieces: 4 latches, rubber seals, screws and chrome nuts.This kit is a great saving over buying all the parts ind...
These Mirrors are made in the U.K. by Tex. Slightly convex lens gives excellent rearward visibility. Right side, left is GAM218A. For fitment to laters cars originally fitted with plastic mirrors, use fitting kit M90999.
See als...