£48.75 exc vat
£58.50 inc vat
In stock
£48.75 exc vat
£58.50 inc vat
In stockRecommended usage 1 x BLS541 to fit one mini.
Genuine Rover/Unipart 4 high quality silicone plug leads for twin point injection minis. For use with M4 type coil.
Genuine Rover/Unipart 4 high quality silicone plug leads for twin point injection minis. For use with M4 type coil.
Set of 4 ignition leads from the original supplier to Unipart, suitable for all twin point minis 1997 onwards. For use with M4 type coil.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Set of 4 ignition leads from the original supplier to Unipart, suitable for all twin point minis 1997 onwards. For use with M4 type coil.
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
This is the bracket that bolts to the front of the mpi blocks to hold the more modern type coil pack. The original type is no longer available so we had this made in stainless steel.
CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference!
After removing the cap you can select between 16 different curves by using
a screwdriver. A bright flas...
Double bullet connector used to join the front loom to the rear loom enar the wiper motor.
Repair loom and plug for all post 1976 headlamp switches.See PM08 for headlamp switch with plug and correct wires colours for loom repair
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
Printed circuit board for 1989 to 1996 3 clock Nippon Seiko type Mini gauge clusters. These have been unavailable for many years but have now been remade exclusively for Minispares.
Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.
The current large plastic shield without any fittings or clips, to cover the engine electrics. Might need slight modifications for some SPI cars but we have fitted them on our own cars without any problems.
The plastic clips are available as...
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For an...
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system.For any ...
Original mini coil fitted to all cars up to 1983.
3ohms
NOT for ballast type ignition systems.
Our research, sales and feed back shows Intermotor coils to be the best available for the mini.
Original type coil bra...
Solid state ignition coil. M4 type for twin point injection minis.
Plugs on the current MPI coils are very snug but do fit.
universal battery clamp replacement with securing bolts and marked N
Only fitted to turbos where it had electronic ignition without points and condenser to cope with extra heat. It was easily recognisable by its blue colour but they are now black. The rotor arm for this is GRA2130
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.