£175.00 exc vat
£210.00 inc vat
Out of stock
Very similar to the Swiftune SW5 this is the ultimate street cam giving power from 1000-5000 revs with wonderfull low emmissions for those who suffer at MOT time--The cam profile was i...
£175.00 exc vat
£210.00 inc vat
Out of stock
Genuine Mini Spares camshaft,great for all road uses- A Plus slot drive only.
Valve clearance should be 0.014" on inlet and 0.016" exhaust. LCA 107 degree
DURATION INLET 264 EXHAUST 268, LIFT INLET 264 EXHAUST 289.
This ca...
Mini Spares cam follower with original convex bottom Radii as used by BMC/Rover and made by Clanceys but less the oil hole. Using Clancey drawings and to our design for better cam performance and lift we have made the push rod recess deeper for stabi...
The original stabiliser kit with cone shaped spacers to strengthen up the rubber bushes against engine movement. Kit includes 4 cone plastic shaped inserts and 4 bushes. The cone shaped inserts push the rubber out in the middle of the engine steady b...
Direct replacement rocker shaft. Fits all except full needle roller types. Far superior to the stock item! ENSURE YOU ALWAYS TIGHTEN DOWN ALL POSTS EQUALLY to eliminate stress fractures on shaft.
Our special "heavy duty" shaft has ...
That tell tale puff of blue smoke when you first start is an indicator of worn guides or seals. Valve guides should be replaced with every valve job.
Sold individually, these are the original quality Cooper S guides for use in any head espec...
Mini Spares own Universal gasket set for solid wall blocks
For any manual block, includes gaskets for "A"Plus and pre A Plus timing covers, but is less tappet chest cover gaskets. Does not include clutch oil seal.
We now offer an en...
Standard weight, 44.00grams, follower with oil drain hole. Always check for wear and replace whenever a new camshaft is fitted. These are manufactured by the supplier to AE Hepolite the original engine components manufacturer and should be coated wit...
Plastic tensioner pad to take up the slack in single row timing chains on A plus engines that wears and should be replaced nearly every time you have the timing cover off. From engine numbers 99H791/10H791 AND ALL A+. Fitted to 998/1100cc from 1979 a...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
For minis with original inertia type starter. The block hose is 12" long and the filter hose is 14". If you want longer hoses see clubman kit MOC100102 block hose 14.5" long and 24" long filter pipe. Pre engaged starter type cars upto 19...
It is critical to understand that an oil cooler is not designed to last the life of the car. Sound maintenance practice tells us that whenever we are doing a major engine overhaul we should not fail to replace the cooler as it is almost impossible to...
Paper gasket for either side of the spacer on all mechanical fuel pumps fitted on the rear of engines. The spacer with gaskets fitted is available as GUG705603GM.
Cup type core plug for all A plus and 1275cc engines except for Cooper S. 33.6mm wide.A plus 5 required but only 4 on 998 A plus. 1275 has 2 core plugs oil pump end of block whereas 998 only has one
Adjustable cam gear set with non stretch chain. Cam gear weighs 674g
Even a stock camshaft needs to be timed correctly. If you want to get the maximum benefit from a "hot" cam it is doubly important that the cam timing be correct. This adju...
Countersunk screw for holding the front palte to the crankshaft bearing cap on cars fitted with duplex gears to give the clearance required. 2 required per car.
The last Rover update on the upper engine stabiliser bar.
A one piece silent block type bush was fitted at both ends from 1996 on and will fit any cars that have 2 bushes fitted at either end as original.
These have also been fitted...
Fits on the engine bay bulkhead for the master cylinders to sit on and for the engine stabiliser bar upper location. The lower part of the stabiliser arm bracket which is welded to the body is 14A6730.
This is for cars with a dual line brake...
Genuine head gasket set to suit A plus engines with the late head gasket which is considered one of the best. For all models with HIF44 and HIF38 except it has no elbow gasket for HIF38 carb to air cleaner.
See GUG701114HS for H...
Genuine Mini Spares product to original drawings and specifications but NOT the original supplier as sold by Rover. The last Rover type supplied were very poor fitting copies where the holes were not correct and the rubber was of spurious quality.
This is the metal plate to blank off the mechanical pump hole on the engine block. No longer available from Rover but Mini Spares have them.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.