MANIFOLD INLET HS4 1.5 BORE SIZE L149
C-AEG490

£178.29 exc vat

£213.95 inc vat

In stockIn stock
The Maniflow steel intake manifold has established the standard by which all others measure themselves. This manifold is specially designed to maximize air flow within the space requirements of a Mini. It accepts either twin 1 1/2" or twin 1 3/4" ...

£178.29 exc vat

£213.95 inc vat

In stockIn stock

Recommended usage 1 x C-AEG490 to fit one mini.

People also bought products

Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.


...

This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...

Smarten up your engine bay with these stainless steel nuts which are not only stronger and resistant to rust but the multi point nut heads are easier for access. See also kit C-STR287.

The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...

Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...

Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG

The newest development in the A-series engine is the use of these nuts with swedged-on washers. The washer will not separate from the nut, so you won't lose it. Yet the nut rotates independently while you tighten it. What a great idea.

The Maniflow steel intake manifold has established the standard by which all others measure themselves. This manifold is specially designed to maximize air flow within the space requirements of a Mini. It accepts either twin 1 1/2" or twin 1 3/4" ...

Manifold stud for all A series injection engines and some late carburettor cars which is 45mm long-6mm longer than 53K487.carburettor engines usually retained the 53K487 shorter screw for the outside 2 holes.

Sold singly,6 per c...

Standard brass manifold nut. You will probably want a mix of these and the longer 51K1177 to secure your intake/exhaust manifold. This nut 5/16" long whereas 51K1177 is 1"long.

Return spring kit for HS4 carburettor spindle.

Also denoted by its black plastic base. Twin HS4 carbs have 30 degree float bowl angles and therefore this jet is easier to fit as it is longer. L/H carb uses AUD9098A std single HS2 jet.



For...

Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...

For HIF38 carbs,this is the full rebuild kit with the spindle and throttle disc and bushes--- see CSK94 for service kit

Metal bracket that fits between the manifold and the HIF44 (1.75")carb to hold the cable - the choke cable clip for this bracket is CZK6491. Also for HIF38. For HS4 carb see 12G766 bracket. Original Turbo type [...

THIS CARB IS A GREAT TUNING AID ON TUNED ENGINES, ESPECIALLY 1380cc.

Fuel or water T piece adaptor

used when upgrading fuel system size on specials from 1/4" to 5/16" or any other modifications

This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.

Jet bearing kit for HS4 carb for swinging needle type. This includes the adjusting nut, spring etc.

jet for HIF38 carb and is 0.090 size--for HIF44 see WZX1453A