PISTON RING SET EARLY 1275GT & S STD
RA21576-00

£34.30 exc vat

£41.16 inc vat

Out of stockOut of stock
RING SET FOR 1275 STD. 4-RING PISTON. RING THICKNESS .0625 and 0.1562" oil rings.For later piston 19320 with 2 rings and an oil ring with the same ring sizes- keep the third ring as your second ring which should be of an oil scraper type, and usually the top 2 rings are the same so discard one of them, but check before fitting.

RA26686 and BHM1166 were the original ring set numbers for the 3 ring type

£34.30 exc vat

£41.16 inc vat

Out of stockOut of stock

People also bought products
PISTON RING SET FOR 21253 PISTON
R41570-00

3mm OIL RING with compression ring size .0591" (1.5mm)and one piece oil ring .1181" (3mm)on p21253 pistons giving 9.7cr on 1275cc. std ring size

For performance see steel ring set with 3 piece oil ring as favoured by engine builders[link]C1...

£70.32 exc vat

£84.38 inc vat
PISTON RING SET FOR 21253
R41570-20

3mm OIL RING with compression ring size .0591" (1.5mm)and one piece oil ring .1181" (3mm)on p21253 pistons giving 9.7cr on 1275cc. 20 thou oversize

For performance see steel ring set with 3 piece oil ring as favoured by engine builders[link]...

£70.32 exc vat

£84.38 inc vat
PISTON SINGLE 1275 LOW DRAG +40 8.8CR
P21251-40

40 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.

Typically installation will result in a minimum 8.8:1 compression ratio but on some pre 1984 Metro versions it was higher.

Current...

£48.00 exc vat

£57.60 inc vat
ENGINE TO GEARBOX NUT AND BOLT KIT
MSSK060

Complete nut, bolt and washer set for engine to gearbox only

£3.50 exc vat

£4.20 inc vat
PUSH ROD 1275 AFTERMARKET
AEG314MS

NON GENUINE for standard use only. These are the only type available at the moment and not as accurate as the original Rover product. The genuine factory pushrod was a very good product and does not need routine replacement. The strength and size of ...

£2.70 exc vat

£3.24 inc vat
CRANK THRUST WASHER SET 1275
VPW41

Set of std VP thrust washers for 1275.

£14.25 exc vat

£17.10 inc vat
OIL PRESSURE RELEASE VALVE COPPER WASHER
6K431

The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...

£0.36 exc vat

£0.43 inc vat
FAN BELT ALTERNATOR when CAM6408 pulley and altern...
GCB10838

Fit minis with latest A plus water pump pulley 4.75"wide CAM6408 and an alternator. Mainly used on 998cc. This belt is slightly longer than GCB10825 so always keep a spare so you know which size belt fitted your car best. La...

£5.79 exc vat

£6.95 inc vat
OIL PUMP "S" EVOLUTION OIL PUMP
C-AEG410

Mini Spares exclusive! "S" 2 bolt fitting, long pin pump.


Almost all pumps available today have the same design capacity. The problem is the lack of precise manufacturing. Most factories in their quest for production volume have sacrific...

£93.75 exc vat

£112.50 inc vat
ENGINE BUILD LUBE TORCO.4 Oz
KCLUBE

Favoured by proffessionals for press fitting pistons, pre lubing bushes, roller and plain bearings, journals and gears. Prevents scuffing, seizure, wear, rust. Waterproof and corrosion proof.

£10.88 exc vat

£13.06 inc vat
GEARBOX TO BLOCK GASKET SET - GENUINE MINISPARES
GUG703049SG

Genuine Mini Spares green and black upgraded Klinger gasket set. 3 pieces



Has the extra front gasket required for 3 synchro case use

£5.48 exc vat

£6.58 inc vat
CRANKSHAFT A PLUS 1300
CAM6232

1275 crankshaft - The A-Plus crank has fillet-radius journals and 1.75" wide rod journals. Siutable for 1275cc Minis, Austin Americas and Mini Metros.



Not supplied with bearings.

£600.00 exc vat

£720.00 inc vat
CRANK THRUST WASHER SET 1275 3 THOU OVERSIZE
AEW2136-003

Set of +.003 thrust washers for 1275.

£7.60 exc vat

£9.12 inc vat
DUPLEX CHAIN AND GEAR SET LIGHTENED AE CAST .NOT F...
C-AJJ3324

Lightened cam gear duplex timing gear and chain set. Not recommended for race/rally applications. approx 69-70g 9% lighter

General: Camshaft Drive Systems


For highly tuned engines always use steel duplex as cast is nowhere as st...

£38.49 exc vat

£46.19 inc vat
BIG END SET 10 OVERSIZE 1275 EXCEPT COOPER S
AEB91306-10

Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S

( Tri-Metal )

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

Tin ...

£28.50 exc vat

£34.20 inc vat
HEAD STUD BLOCK TO HEAD SHORT 4" UNC 3/8"
CAM151

You require 5 of these high tensile short head studs and they torque to 42lb/ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud [link]C...

£4.28 exc vat

£5.14 inc vat
BIG ENDS SET STANDARD 1275 EXCEPT COOPER S
AEB91306-00

Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S

( Tri-Metal )

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

Tin ...

£28.50 exc vat

£34.20 inc vat
TIMING COVER OIL SEAL ALL PRE 1992
88G561

Genuine Mini Spares Original black timing cover oil seal for all A series until the introduction of a new type of lip seal introduced in 1991 mainly for injection engines, when they changed to LUF10006--albeit many owners fit this not kn...

£1.80 exc vat

£2.16 inc vat
DUPLEX TIMING CHAIN.DOUBLE ROW ENDLESS
2H4905

For race quality chain see 2H4905EVO.

It only makes sense that if you have your engine out of the car that you replace the timing chain. The chain controls the timing of the camshaft and even a slight amount of wear or stretch c...

£5.78 exc vat

£6.94 inc vat
ENGINE BLOCK SET 1300 pre A plus
GUG701615CS

genuine block gasket set for 1300 without tappet chest seals or clutch seal

£20.06 exc vat

£24.07 inc vat