FUEL GAUGE (BF6108-00) 1964-83
13H2133

(¥45) £45.36 exc vat

(¥54) £54.43 inc vat

In stockIn stock
In 1964 the fuel gauge system was changed on the Mini (pre" 64 cars did not have a voltage stabilizer). It is necessary to match the gauge with the tank sending unit and the supply voltage…if your readings are way off…always full or empty or max 1/2 ...

(¥45) £45.36 exc vat

(¥54) £54.43 inc vat

In stockIn stock

Recommended usage 1 x 13H2133 to fit one mini.
Speedos, Gauges, & Cables - Qty 1

People also bought products

Brand new modern electronic version of the classic centre speedo, housed in a billet case with OLED display this unit fits as per original speedos. Features include:



*Trip and total miles

*Remote trip reset

*Driv...

This is the bulb holder for the original Smiths auxillary gauges fitted to 3 clock centre dashboards i.e 13H4459 and 13H4460, will also fit the aftermarket Smiths gauges (SIB part numbers).

Sealing washer for the oil gauge to oil pipe as sold in OL kit and for 21A804 metal pipe to oil gauge.

Voltage stabiliser for clubman/2-3 clock side pod(smiths) up to 1988. Three terminals/br1303/20.

With this large diameter line to the oil pressure guage you can actually see minor fluctuations in the pressure at idle or when the relief valve bounces open and closed. Because the braided steel line is one piece from the block to the gauge there is...

We sell about 20 of these per year and many are used on similar models to those indicated-Main and dash loom only--No side wing indicators-indicator stalk on right-alternator-rear lamps with reverse lights-steering lock-inertia starter-centre speedo ...

Angled oil pipe adaptor for fitting in confined spaces to eradicate damage of oil pipe, requires an OA adaptor if being used with a oil pressure gauge/t-piece.

Oil pipe in plastic 5 feet long, if fitting to a Tim gauge you will require LMA017 adaptor for the gauge.

Not comppatable with the CAM6431 standard oli pressure block union, and OA shoudl be purchased to fit.

Oil gauge adaptor for fitting into engine block or T piece.

A must if you want to run a mechanical oil gauge and retain the oil warning switch. Screws straight into the block on all A series engines.

Male to female brass spacer/adapter for mechanical water temp guage screws into head & accepts capillary tube. Required for SIB422 and SIB422MG. Also fits in MOCOT1

Speedometer cable, 30" long for Smiths type central speedo-original was 26" long

Mini Moke Speedo Cable for the Centre clock type speedo,also 13" longer to allow the Smiths type central speedo to be moved.

If you have an early Mini saloon or Estate/Van or Pickup with the fuel tank sending unit held in by screws, this is the correct screw for you.

Do not forget the special copper washers also 2A2088 and the cork gasket [link]2H10...

Oil pressure is the "blood pressure" of your engine! Know how it is doing and you know how your engine is doing. This Smith's gauge is the standard 2" diameter with chrome bezel. With a magnolia face. Mechanical.

Does not come with pipewor...

Oil pressure is the "blood pressure" of your engine! Know how it is doing and you know how your engine is doing. This Smith's gauge is the standard 2" diameter with chrome bezel. Mechanical.

Does not come with pipework,bulb holder or bulb.

Extra long cable for Smiths central located speedo when position moved in dash and also used as a Tacho cable for Sprite, 36" long.

48" extra long speedo cable for special fitmentswhen using original type Smiths central mounted speedo.

Electric water gauge as standard on the centre binnacle Mini. Marked "C-N-H" Genuine Smiths. With a magnolia face.



Does not come with bulb holder or bulb.

Electric water gauge as standard on the centre binnacle Mini. Marked "C-N-H" Genuine Smiths. For post 1964 vehicles with voltage stabiliser fitted on speedo.

The early type had 3 connector tabs on one long brass strip for wires where as thi...