AC DODD ROAD TORQUE CAMSHAFT
ACD-RT

(¥214) £214.40 exc vat

(¥257) £257.28 inc vat

In stockIn stock
AC Dodd Road Torque cam, great for low end power. Please see picture for full cam specs.



Road torque, this cam for strong low & mid range lugging, Touring, Smooth idle, excellent emmisions



ACD - RT

Power...

(¥214) £214.40 exc vat

(¥257) £257.28 inc vat

In stockIn stock

Recommended usage 1 x ACD-RT to fit one mini.

Recommended products

Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up

A vital aid for accurately timinig non-factory camshafts. This disc is a 360 degree protractor disc made by kent cams.

People also bought products

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up

If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.

Glyn Swif...

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.

This chain saves all the time and effort requ...

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all 1275cc blocks plus 970 and 1071 Cooper S. It's almost too simple and thus often overlooked during a rebuild. Camshaft bearings are pressed...

NON GENUINE for standard use only. These are the only type available at the moment and not as accurate as the original Rover product. The genuine factory pushrod was a very good product and does not need routine replacement. The strength and size of ...

Rover piston TAM2048 stamped 21962 with ring sizes 1.501mm and oil ring 4mm but some pistons have been stamped 21963.

-Does this get confusing?

So lets clear it up; the easy way to identify the piston and corrrect rings are as follo...

20 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.

Typically installation will result in a minimum 8.8:1 compression ratio but on some pre 1984 Metro versions it was higher.

Current...

Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...

Genuine Mini Spares Klinger timing chain gasket for any BMC A series engine with 10 gasket holes, fitted until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.

The klinger m...

Favoured by proffessionals for press fitting pistons, pre lubing bushes, roller and plain bearings, journals and gears. Prevents scuffing, seizure, wear, rust. Waterproof and corrosion proof.

Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S

( Tri-Metal )

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

Tin ...

Genuine Mini Spares Original black timing cover oil seal for all A series until the introduction of a new type of lip seal introduced in 1991 mainly for injection engines, when they changed to LUF10006--albeit many owners fit this not kn...

Main bearings, 1275 2" mains.STD size. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.

Sintered copper lead, lead plated,steel backed