(¥37) £36.99 exc vat
(¥44) £44.39 inc vat
In stock
In the past, fitting an oil cooler was mandatory once an engine had been even slightly uprated. The main reason for this was the quality of motor oils available at that time. If the oil temperatures regularly exceeded a specific point(100c) engine failure was almost guaranteed. Modern motor oils are generally of a much higher quality, especially the 'brand names', and have far superior high temperature tolerance than those of 10 or 15 years ago. Fully synthetic oils have extremely high heat tolerance. Use of any of these oils makes an oil cooler less of a necessity where engine outputs don't exceed about 90 horsepower. It is as bad to run the oil temperature too cool as it is to let it get too hot. The ideal operating range is 200 to 230 degrees F (sump temp). At these temperatures the oil is working efficiently to produce the best power, economy and release of combustion by-products. If the oil is too cool, these by-products are absorbed into the oil, requiring more frequent changes to avoid bearing and bore damage. It is worth noting that keeping the oil at the correct temperature helps cool the engine; high oil temperatures will create higher water temperatures.
Various sizes of oil coolers and fitting kits, including pipes, are available. To help control temperature this thermostat fits into the engine cooler pipes (can not be used with braided steel pipes) that starts to operate at 75 degrees C (165degrees F) and fully shuts off at 85c allowing oil cooler to completely function which is considered perfect for road use. An oil temperature gauge adapter MOCOT2 is also available that fits into one of the cooler pipes, not compatible with the braided steel pipes.
(¥37) £36.99 exc vat
(¥44) £44.39 inc vat
In stockRecommended usage 1 x MOCOT1 to fit one mini.
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
Oil cooler union for later cars, will fit the oil filter head and block, 1/2" BSP to 11/16". Requires DSM18 to seal. These are handy when you have changed to a later filter head etc and want to fit an early oil cooler kit.
Oil cooler kit for MPI models. Oil cooler is 10 rows, 21cm long and 9cm high. Unions are 18mm and require the special fitments as supplied in this kit. The oil filter is GFE210
5/8" straight connector piece for heater hose modifications on late minis.
Useful when re-routing hoses or joing hoses.
1" long from bend to take a push on fit 1/2"hose-has 1/2"BSP thread to fit oil cooler and has 45 degree angle bend
For minis with 5.8"UNF size oil pipe block hole.1/4"NPT filter (pre 1992 12A engine)but with a pre-engaged starter longer pipes are required 15"block and 22" filter length
1" long from bend to take a push on fit 1/2"hose-has 1/2"BSP thread to fit oil cooler and has 90 degree angle bend
For minis with 5.8"UNF size oil pipe block hole 1/4"npt filter head (pre 1991 12A engine) but with a pre-engaged starter longer pipes are required 15" block and 22" filter.
Set of engine block and filter head unions for pre 12A engines (1992).
these take push on oil cooler hose.
These braided oil cooler hoses are the best available and although longer for the mini clubman many mini racers use these for the extra length to enable fitting to a standard mini. Short Pipe: 14" Long Pipe: 24"
"LONG" Oil Cooler Hoses
A 15" & a 25" long line makes these kits ideal for those wanting to relocate the oil cooler!
Oil temperature sender unit housing for checking oil temperature.
Fits into the oil cooler hose.(Not compatable with braided hoses) Fitted before the oil cooler will show maximum temperature reached. After the oil cooler it will tell you the...
Whether you are installing a cooler from scratch or merely need to replace your tired old rubber hoses, you'll like the looks of this stronger Braided hose kit. The hoses are fully assembled, with the proper fittings in place and even include the nec...
Special formulated hose for oil, this is for people who have special oil cooler fittings and ends that use lengths of hose. This 1/2" hose is also used for all closed circuit breather systems and uses 3H2963 clips. SOLD AS REQUIRED PER F...
Usefull joining union for 1/2" water hoses and used for oil coolers hoses.
The original union that fitted on the A series block to take the oil cooler hose. Many kits now include the union as part of the hose. Filter head size 1/4"NPT.
For minis from 1992 with a 12A engine. The block hose is 15" long and the filter hose is 22". The block has 11/16"UNF oil pipe hole thread.
These are the original brackets (2 required) used to fit on the front subframe to hold the oil cooler. For later cars check you have clearance.
SOLD INDIVIDUALLY.
It is critical to understand that an oil cooler is not designed to last the life of the car. Sound maintenance practice tells us that whenever we are doing a major engine overhaul we should not fail to replace the cooler as it is almost impossible to...
genuine Mocal UK cooler.This is the ideal size for minis, but everybody goes for the 13 row type cooler radiator C-ARH221 which was fitted to the Cooper S eventually as standard but that was over 30 years ago, before the later type oils ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.