(¥48) £48.00 exc vat
(¥58) £57.60 inc vat
In stock
Typically installation will result in a minimum 8.8:1 compression ratio but on some pre 1984 Metro versions it was higher.
Current pistons differ from the 60s originals, improved with a "low drag" slipper skirt design and a shorter lighter wrist pin.
Wrist pin height is 1.4689", crown has 8cc dish, and they have two 1.5mm compression rings and a 4mm oil ring.
From the top ring to crown these measure about 7mm and the high compession P21253 piston have 10mm gap from top ring groove to crown.
Ringset is R35960-40.
Sold singly,4 per engine required
Now Nural stamped 87-521711-00
AE Hepolite is now owned by Federal Mogul and trademarked "Nural".
(¥48) £48.00 exc vat
(¥58) £57.60 inc vat
In stockRecommended usage 1 x P21251-40 to fit one mini.
Low drag 1275 piston standard size 2.780 plus 40 thou oversize(Rings included).
This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.Engine then becomes 1310cc
Current pistons differ from the 60s origi...
Mini Spares Evolution Lightweight Performance Piston-single piston and rings.
Press fit only. Same design as C-STN103 but different manufacturer
The ultimate in lightweight die cast pistons, available in +.020, +.040 & +.060 sizes,...
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980o...
60 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.
Typically installation will result in a minimum 8.8:1 compression ratio but on some Metro versions it was higher.
Current pistons ...
4mm oil ring. These rings fit the current replacement pistons from AE Hepolite range 21250 and 21251 low drag slipper type with 8.1 cc dish and only piston 21251 is now available 8.8CR.
Rover piston TAM2048 stamped 21962 with ring sizes 1.50...
Available at the moment but they sporadically become unavailable. Mini Spares have also had a batch of plus 60s specially commissioned to us for Grass trackers and racers. sold individually with rings and pin complete.
Ringsets are availabl...
RING SET FOR 1275 STD. 4-RING PISTON. RING THICKNESS .0625 and 0.1562" oil rings.For later piston 19320 with 2 rings and an oil ring with the same ring sizes- keep the third ring as your second ring which should be of an oil scraper type, and usually...
Rover piston TAM2048 stamped 21962 with ring sizes 1.501mm and oil ring 4mm but some pistons have been stamped 21963.
-Does this get confusing?
So lets clear it up; the easy way to identify the piston and corrrect rings are as follo...
Rover piston TAM2048 stamped 21962 with ring sizes 1.501mm and oil ring 4mm but some pistons have been stamped 21963.
-Does this get confusing?
So lets clear it up; the easy way to identify the piston and corrrect rings are as follo...
20 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.
Typically installation will result in a minimum 8.8:1 compression ratio but on some pre 1984 Metro versions it was higher.
Current...
NPR Ring set for 73.5mm Mega and Omega pistons with 1.2mm thick rings and 3 piece oil rings-also for new range of EVO pistons C-STN101
This piston for 1098cc engines was designed with 4 rings. The top three compression rings are .0625" thick and the bottom oil ring is .1575" thick. Pin height in this piston design is 2.2855", this results in a compression of 8.5:1 in most standard ...
ringset for powermax 20659 piston with groove sizes 1.5mm and 4.00mm for one piece oil ring -ring measurements are slightly under this --the tapered ring with the ridge fits second groove down-
STD size low drag slipper type pistons with a minimum 8.8:1 compression ratio but on some Metro versions it was higher.
Current pistons differ from the 60s originals, improved with a "low drag" slipper skirt design and a shorter lighter wri...
Low drag 1275 piston standard size 2.780 plus 40 thou oversize(Rings included).
This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.Engine then becomes 1310cc
Current pistons differ from the 60s origi...
AE Hepolite +20 Engine set of rings for C-AJJ3378/20 C-AJJ3382-60 Mega and Omega pistons when rings are 0.0470"(1.2mm) and 0.1575" 4mm oil rings.
For latest spec race quality NPR rings see C-STN102-20
Sold as a single piston and although for Turbos is from original Rover casting and tooling to run on 5psi turbo boost. Now with 9.38cc. They use our mega ringset C-AJJ3379-40.
If using more boost you need to be working on a low...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Set of +0.030" size 1275 crank thrust washers.
Set of +0.003" size 1275 crank thrust washers.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.