CIRCLIP FOR VALVE COTTER 2A11EVO
2A12

($0.87) £0.87 exc vat

($1.04) £1.04 inc vat

In stockIn stock
Circip, this tiny hairpin clips over the early valve spring collets 2A11EVO. Although Leyland said they were not required any longer on a bulletin around 1970 most people regard them as an extra safety part as the collets always looked a loose fit.

($0.87) £0.87 exc vat

($1.04) £1.04 inc vat

In stockIn stock

Recommended usage 8 x 2A12 to fit one mini.
Cylinder Head 850CC, 998CC & 1100CC Pre 'A' Plus - Qty 8
997CC & 998CC Cooper Cylinder Head - Qty 8

Recommended products

Smal O ring that sits on the valve stem on all 850 and early 998 cylinder heads with large collet grooves.

New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the v...

People also bought products

New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the v...

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the valves and easier to control spring heights.

Alloy CNC version of the cylinder head take off 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does

Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:

Inlet/Exhaust manifold to head, studs/nuts/washers

Thermostat housing (no sandwich plate) studs/nuts/washers

H...

Minispares own stainless steel Thermostat housing stud kit for the single tier type thermostat housing.Quantity required one kit per car

This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket

Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.

Man...

1.2"(31mm) intake valve for 12G295 Cooper head 998cc. Also a suitable upgrade for other small bore heads. These have the large collet groove 8.65mm (.340") 2A11 cotters which are now available as 2A11EVO. Correct grade exhau...

Originally fitted to Minifin rocker covers as standard Rover equipment, it will also fit almost every other rocker cover including our FP26 range and Minispares alloy covers. This improved cap has a large grip and an improved lock system...

Standard inner valve spring lower collar, use C-AEA654.

These are no longer required when using our C-AEA526 and C-AEA527 range of silicone wire springs which are a slight interferance fit and friction ...

A true Cooper S engine has 10 studs and one specially designed bolt.

Best quality 1" exhaust valve for small bore cylinder heads as fitted standard to 998 Cooper. Higher grade than AEA434. Has a large 8.65mm (.340") collet groove 2A11 cotters which are now available as 2A11EVO.

1.1" diameter intake valve for 948cc with 8.65mm wide groove for use with the original 88G616 top caps and 2A11 cotters which are now available as 2A11EVO.

160lbs on the nose at 400" for standard Cooper S or twin spring set ups. See C-AEA526 and C-AEA527 for later developed springs. These are ok for all standard uses but are improved and uprated over all original factory fitted...

Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.

We have no evidence as yet that they last longer but do look good.

See [lin...

Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...

Early Large cotter groove exhaust valve. Most small bore engines seem particularly prone to burning valves, it is highly recommended to replace the exhaust valves when you do a valve job! This 1.0" valve fits most early 948cc, 998cc and 1098cc engine...

Chrome Rocker bolt with UNF thread. Original Rocker cover bolts are dull zinc coated or painted but the chrome type look much better and cheaper.

A longer threaded version CAM6823 was used on prestige Minifin alloy type A series...

This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...