Victor Reinz/Mahle small bore head gasket for A-series engines.

Gasket fitment. Writing side up.

($10.40) £10.40 exc vat

($12.48) £12.48 inc vat

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

($16.14) £16.14 exc vat

($19.37) £19.37 inc vat

VALVE SPRING SEATS SHIMS 0.020"(set of 4)

SS1

Spring seat shims (set of 4), 0.020" thick (0.5mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...

($6.90) £6.90 exc vat

($8.28) £8.28 inc vat

VALVE SPRING SEATS SHIMS 0.040" (set of 4)

SS5

Spring seat shims (set of 4), 0.040" thick (1mm).

Spacer shims to increase valve seat pressure and overall spring rate.

These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT36...

($7.59) £7.59 exc vat

($9.11) £9.11 inc vat

TIMING COVER AND FRONT PLATE FITTING KIT

MSSK063

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

($8.00) £8.00 exc vat

($9.60) £9.60 inc vat

ROCKER ADJUSTING NUT EN24T

C-AHT450

Mini Spares genuine upgraded part. Hexagon head rocker screw nut in EN24T.

Also available is a flanged nut C-AHT449

($2.64) £2.64 exc vat

($3.17) £3.17 inc vat

11/16" DOWTY SEAL

DSM18

11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102

($2.40) £2.40 exc vat

($2.88) £2.88 inc vat

USED distributor spindle pre A plus

12G4499MS

"used old"Distributor drive,all pre A Plus A series engines plus MGB.

Fitted in the engine block to drive the distributor these were made obsolete in 1988 by Rover so if you have lost yours we have a few of these used shafts to keep yo...

($24.00) £24.00 exc vat

($28.80) £28.80 inc vat

OXYGEN SENSOR LAMBDA UNIT (SPi & MPi) BOSCH

MHK10004BOSCH

Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.

($78.57) £78.57 exc vat

($94.28) £94.28 inc vat

CYLINDER HEAD HEATER TAP FITTING KIT

ADU9102FK

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

($1.60) £1.60 exc vat

($1.92) £1.92 inc vat

SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275 +40

C-STN103-40

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

($299.00) £299.00 exc vat

($358.80) £358.80 inc vat

SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275 +60

C-STN103-60

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

($299.00) £299.00 exc vat

($358.80) £358.80 inc vat

MINI 1275 CAM LINER SET

MS3063

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

($15.75) £15.75 exc vat

($18.90) £18.90 inc vat

PISTON RINGS FOR EVOLUTION +20 PISTON

C-STN102-20

Race quality single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.

sold per piston so 4 packs required per engine

($16.00) £16.00 exc vat

($19.20) £19.20 inc vat

PISTON RINGS FOR EVOLUTION +60 PISTON

C-STN102-60

Race quality Single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring--sold per piston so 4 packs required per engine

($16.00) £16.00 exc vat

($19.20) £19.20 inc vat

LOWER POLY STABILISER BUSH KIT

C-STR633

Stabiliser bush kit for lower engine steady

($14.40) £14.40 exc vat

($17.28) £17.28 inc vat

CRANK THRUST WASHER SET +0.003" 1275

ACL2136-003

Set of +0.003" size 1275 crank thrust washers.

($11.25) £11.25 exc vat

($13.50) £13.50 inc vat

ARP 11 STUD HEAD SET

C-AHT283

ARP Head stud kit that compromises of;

4 x Long Head Studs

7 x Short Head Studs (Disregard 2 if you're using a 9 stud application)

11 x Multipoint ARP nuts

11 x Heavy Duty Washers

4 x Rocker post studs <...

($142.50) £142.50 exc vat

($171.00) £171.00 inc vat

MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...

AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.

Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

($26.00) £26.00 exc vat

($31.20) £31.20 inc vat

MAINS +10 1275CC A PLUS ONLY ACL RACE

C-AEM91886-10

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

($78.62) £78.62 exc vat

($94.34) £94.34 inc vat