($19.50) £19.50 exc vat
($23.40) £23.40 inc vat
($19.50) £19.50 exc vat
($23.40) £23.40 inc vat
Recommended usage 1 x CZH120 to fit one mini.
Front of door frame repair panel down to door step R/H non genuine
L/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
R/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Really a built up half front end for the mini clubman, consists of a lower panel with headlamp panels,slam panel and stiffener between the front and slam panel. 76 ON--no inner or outer wings
Commercial Mini floor extension
It is an essential part for the correct restoration of all the longer wheelbase mini derivatives. From the original tooling.
genuine front panel for the mini clubman before 1976 when the subframe was rubber mounted.see AAM1022 for rubber mounted type as fitted from 1976 on.
the front of these panels is the same but the subframe mounting bracket on the...
The only bonnet landing panel available for the clubman shape body for a long time this part is perfect in every detail and was used on the heritage bodyshells.
A Genuine panel is now available from BL Heritage CZH149.
...
Aftermarket version of the L/H floorpan for 1991 on cars.
This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 199...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
1970 on, cars with internal hinges and wind up windows
This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section of inner wing
If your rusted old headlight bucket is getting to you, don't waste time trying to salvage it when new metal reproduction metal buckets are AVAILABLE.
With a headlamp rim fixing bracket 37H7421 attached
Whether you are ...
1970 on, cars with internal hinges and wind up windows
This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
This panel has mounting holes for later models facia crash panel. These holes will require blanking for true originality on earlier models without the facia pad
floor pan front to rear for the left hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mul...
Floor pan front to rear for the right hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mult...
See ALA5661MS for an upgraded thicker and best fitting aftermarket L/H A panel-all the local bodyshops fit this.
Known as an A panel this is for all wind up widow type cars with internal door hinges and is single skin as opposse...
Aftermarket version of the R/H floorpan for 1992 on cars.
This floor was made stronger to prevent vibration and rust and will fit any Rod change gear shift mini started on the first injection cars