INNER WING PART PANEL L/H SPI 1991-96
CZH3067

($52.20) £52.20 exc vat

($62.64) £62.64 inc vat

In stockIn stock
part inner wing L/H from Damper bracket mounting pointing forward for SPI modles 1991-96 with large round electric radiatore fan hole

NON genuine panel

($52.20) £52.20 exc vat

($62.64) £62.64 inc vat

In stockIn stock

Recommended usage 1 x CZH3067 to fit one mini.

Alternative products

Inner l/h wing with large fan hole from 1991-96. This panel is available with the A panel fitted for ease of fitment as ABD36005

Was ABD36009 but that did not have the stiffener plate for the damper bracket fitted which was diff...

People also bought products

part inner wing R/H from Damper bracket mounting points forward MK1 except Clubman. 1959-69 it has no air hole in side-see CZH3064 for later type with hose hole.

NON genuine panel

O/S/F wing t for 1996 on cars. THIS WING STILL NEEDS MODIFYING to allow for fitting of Sportspac arches and 13" wheels. After trimming/cutting to size remember to replace or renew the stiffener lip ALR360380

Has the headlamp re...

Part inner wing L/H from Damper bracket mounting points forward. MK1/2/3 except Clubman. This panel has radiator cooling slats as fitted to 1991

NON genuine panel only as part panel

part inner wing R/H from Damper bracket mounting points forward MK2/3 except Clubman. 1969-91 not Mk1/2 as it has air hole in side

NON genuine panel

Aftermarket wings do the job at a fraction of the cost of originals. This right front wing for the Mini will fit all MKI, II, III, IV. A slight difference exists between the early and the later models as to headlamp mounting holes. These reproduction...

1970 on, cars with internal hinges and wind up windows

This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section of inner wing

1970 on, cars with internal hinges and wind up windows

This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section

1970 on, cars with internal hinges and wind up windows

This repair R/H panel has holes for the hinges on A post and overlaps 6" at top tapering to 9" at bottom (150mm-215mm) onto the wheel arch section.

Also has the first section of...

1970 on, cars with internal hinges and wind up windows.

This L/H repair panel has holes for the hinges on A post and overlaps 6" at top tapering to 9" at bottom (150mm-215mm)onto the wheel arch section.

Also has the first section of...

Right hand inner wing section only for MK3 cars with 3 air vent holes. One with 4 bolt holes,one with 4 castellated bolt holes (nuts welded in place) and one large trunk hose hole at front. If you want the same panel with A panel combined for better ...

Aftermarket wings do the job at a fraction of the cost of the originals. This left front wing for the Mini will fit all MKI, II, III & IV. A slight difference exits between the early and the later models as to headlamp mounting holes. These reproduct...

These wings have the original round headlamp hole which is okay unless you have the dipping headlamps fitted to some export models and MPI cars--

1997-2000 cars need to use ASB360009 which has the recess for the headlamp adjusti...

Fits all minis with side repeater lamps and an aerial hole from 1988 until 1996 except export models with adjusting headlamps. After 1997 ASB360010 should be used, which has no aerial hole, and a recess for the dipping headlight motor. ...

Fits all minis with side repeater lamp from 1988 up until 1996 except export models with adjusting headlamps.

1997-2000 cars need to use ASB360009 which has the recess for the headlamp adjusting motor. cars registered after 1st...

Minis most used rubber plug 1.25" wide for holes approximately 7/8".

Fits floor, aerial hole and steering column extra hole and radius arm shroud on MK1/2 minis.These floor plugs vary in number from 11 in a Elf/Hornet,Mk1 and 1994 on cars do...

N/S/F wing without ariel hole which was standard fiment for 1996 on cars which had a factory fitted roof ariel. THIS WING STILL NEEDS MODIFYING to allow for fitting of Sportspac arches and 13" wheels. After trimming/cutting to size remember to replac...

The Heritage produced front wings (fenders) for the Mini are the original with

correct round hole for headlamp. They fit. The proper gauge metal and original tooling ensures that even the novice body man can make them work great. Cars regist...

The Heritage produced front wings for the Mini have the correct headlamp round hole. They fit! The proper gauge metal and original tooling ensures that even the novice body man can make them fit properly, no aerial hole or wing side repeater hole. Ca...

These wings have the original round headlamp hole which is okay unless you have the dipping headlamps fitted to some export models and MPI cars--You will have to use the genuine wing if you have dipping headlamps.See BMP455 for cars with...

The last type of rod change rib design floor made for the assembly line fits cars from 1997-2000. It has a large rib down the centre of the L/H side.

This floor produced from genuine tools has the crossmember fitted with the sill panels an...