($129.05) £129.05 exc vat
($154.86) £154.86 inc vat
($129.05) £129.05 exc vat
($154.86) £154.86 inc vat
Recommended usage 1 x HL3000P to fit one mini.
Mk1 1962 on crackle effect cream headling that fitted on 2 hoop type frames whereas the Mk3 had individual rods. This is for Mk1 saloons only. Earlier cars had a light grey headlining which is available to order under HL3000P. (Does not ...
Our lightweight underfelt kit is the perfect companion when fitting a new headlining. Made from lightweight felt and cut to size, this fits into the cavity of the roof before fitting your new headlining and provides increased sound insulation and pro...
This was the first style of sunvisor pad with central pivot point in cream crackle finish used on the early Minis.Some very early minis used pale grey for std but all Supers had crinkle finish cream to match headling. For this period the Cream Crackl...
The clips that hold the seat squab vinyl to the frame on front seats and the headlining. These clips are available seperately as GHF1500.
This universal trim clip with smaller D shape and exta short claws section is for rear seat and for headlings. For MK1/2 minis and Traveller/Estate versions there are 25 and MK3 on there are 13.
For the clip with a larger D and claw spike se...
The chrome moulding to fit the door bin on first 80 thousand MK1 minis with extra length tag with screw hole for location.
This is held on by screws but a single sided prong clips ADH3809 can be used in the centre - beware other...
MK1/2 interior door handle with screw and washer.
This solid "spoon" handle is brittle and easily broken.
These are the original shape as sold under the Unipart label, not the later Rover bagged item which was a reproduction with d...
127cm long and 43cm wide this is enough leather cloth trim that fitted S and deluxe models on the upper and lower facia plus the winscreen A posts. Fitting instructions are included but no glue.
Reproduction gear lever gaiter for all remote control type gearboxes with the short gear lever by the driver's seat. The metal retainer for this gaiter is 14A9942. These were fitted until the introduction of the rod change type [link]CZH...
Plastic window locks for sliding windows, metal ones are no longer available.
24A1194 = Right Front
24A1195 = Left Front
24A1196 = Right Rear
24A1197 = Left Rear
If you have twin original 5.5 gallon tanks this 26" wide boot board is the one for you.
Plastic window locks for sliding windows, metal ones are no longer available.
24A1194 = Right Front
24A1195 = Left Front
24A1196 = Right Rear
24A1197 = Left Rear
Plastic window locks for sliding windows, metal ones are no longer available.
24A1194 = Right Front
24A1195 = Left Front
24A1196 = Right Rear
24A1197 = Left Rear
Seal for door handles MK1/2 and all sliding window exterior hinge cars.
also used on 14A7195 mk1 boot handlle used on mk1/mk2 and van/estate
is oval shaped
for boot / rear door use the hole at the rear ...
This polished aluminium corner plate fits over the leading edge of the MKI/II door pocket to add protection and class. Only the Nearside plate is supplied.
"Remote" gearshift boots 22A608 are readily available in aftermarket quality. Unfortunately, this metal retaining band had been unavailable from normal sources so we at Mini Spares recently took it upon ourselves to have our own manufac...
OEM firewall soundproof. These OEM style soundproof mats will fit right on any MkI/MKII Mini. Cutouts are there for the fresh air hose, hinges, wiring and wiper motor. The felt/jute is flame resistant on one side. You will notice the difference!
Plastic window locks for sliding windows, metal ones are no longer available.
24A1194 = Right Front
24A1195 = Left Front
24A1196 = Right Rear
24A1197 = Left Rear
The lower brightwork moulding for finishing off the lower dash, crash pad rail or on earlier cars the painted metal surface of the panel which holds the switch panel section.See 14A8010 for clip
This moulding was fitted to all m...