($8.00) £8.00 exc vat
($9.60) £9.60 inc vat
In stock
($8.00) £8.00 exc vat
($9.60) £9.60 inc vat
In stockRecommended usage 4 x TAM1330 to fit one mini.
Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
EXHAUST VALVE 1.15 TURBO
.3135 thou (7.96mm) thick, uses CAM6573 collets only.
1.220" (31mm) dia x 3.57 exhaust valve.
Our race valves are produced in EN214N steel and are stellite tipped and use the later narrow, single collet groove and current valve head shapes.These valves are plasma heat treated to eradicate wear ...
1.401" dia x 3.52" long intake valves. Our race valves are produced in EN214N steel, stellite tipped and use the later narrow collet groove and current valve head shapes. As it is possible, even common, to swap one head for another on 1275 engines, i...
Collet for the 3 groove valve. Sold per half and 2 required per valve.
These cotters go with AHU1897 top cap. On Turbo heads after engine number 102641 were fitted on the inlet only.
All early 850/997/998/1098cc heads u...
If you drive A-Series cars long enough you will eventually have to replace the water pump bypass hose. These are the best quality available to fit without removing the cylinder head but these fluted rubber hoses have a bad reputation so if possible ...
Inlet valve 1098cc with small cotter groove.29.2mm(1.15") and takes AEA311 spring.Sold singly 4 required per engine.
That tell tale puff of blue smoke when you first start is an indicator of worn guides or seals. Valve guides should be replaced with every valve job.
Sold individually, these are the original quality Cooper S guides for use in any head espec...
If you want performance then you know you have to get as much air into the cylinder as possible. The bigger the valves the more this is possible. The standard 1275 mini and Sprite motor has only 1.3" intake valves, the standard Cooper "S" has 1.41" i...
1.158" (29.4) dia exhaust valve for 12G940 casting.
Our race valves are produced in EN214N stainless steel and require Manganese/Silicon bronze alloy valve guides. They are stellite tipped and have the triple collet groove and c...
This is the standard size valve with triple groove collets for A plus 1275cc
heads and 3.59 long. If you want the next size up use the TAM1059.
1.402" (35.6mm) dia x 3.57" long intake valve.
Our race valves are produced in EN214N steel and are stellite tipped and use the later narrow, single collet groove and current valve head shapes. They are plasma heat treated to eradicate wear ...
Hardened unleaded valve seats for 1.15" 1275 exhaust valves.
Require a recess of 1.2495"(31.737mm) diameter, plus or minus 0.0005" (0.013mm), and 0.250"(6.35m) deep at ambient temperature of 20C.
Last of the 998cc exhaust valves,lead free with triple collet groove 25.4mm.
Uses 12G1015 springs. will fit from 1984 on --3.42"long
These are the exhaust valve seats for lead free small bore cylinder heads
850/998/1100. If you require inlets see TAM2152.
Fitted from 1988 with introduction of press fit high compression pistons although many earlier h...
For specialised race use only, these springs are 267lb@ 1/2"lift fitted.
(use C-AEA526 for race and fast road cams)
Modern high lift, short duration camshafts have posed quite a few problems for the general public in re...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.