£2.72 exc vat
£3.26 inc vat
In stock
£2.72 exc vat
£3.26 inc vat
In stockRecommended usage 4 x C-AHH8537 to fit one mini.
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
Oil cooler union for the block on pre 1992 cars. This special fitting is 5/8 to -08AN and designed for motorsport customers who want to make their own oil cooler or transfer pipe using the larger -08AN braided hose comonly sold at most motorsport out...
Oil cooler union for the block and filter housing on 1992-1996 cars. This special fitting is 11/16 to -08AN and designed for motorsport customers who want to make their own oil cooler or transfer pipe using the larger -08AN braided hose comonly sold ...
Oil cooler union for later cars, will fit the oil filter head and block, 1/2" BSP to 11/16". Requires DSM18 to seal. These are handy when you have changed to a later filter head etc and want to fit an early oil cooler kit.
Oil cooler kit for MPI models. Oil cooler is 10 rows, 21cm long and 9cm high. Unions are 18mm and require the special fitments as supplied in this kit. The oil filter is GFE210
5/8" straight connector piece for heater hose modifications on late minis.
Useful when re-routing hoses or joing hoses.
1" long from bend to take a push on fit 1/2"hose-has 1/2"BSP thread to fit oil cooler and has 45 degree angle bend
For minis with 5.8"UNF size oil pipe block hole.1/4"NPT filter (pre 1992 12A engine)but with a pre-engaged starter longer pipes are required 15"block and 22" filter length
1" long from bend to take a push on fit 1/2"hose-has 1/2"BSP thread to fit oil cooler and has 90 degree angle bend
For minis with 5.8"UNF size oil pipe block hole 1/4"npt filter head (pre 1991 12A engine) but with a pre-engaged starter longer pipes are required 15" block and 22" filter.
Set of engine block and filter head unions for pre 12A engines (1992).
these take push on oil cooler hose.
These braided oil cooler hoses are the best available and although longer for the mini clubman many mini racers use these for the extra length to enable fitting to a standard mini. Short Pipe: 14" Long Pipe: 24"
"LONG" Oil Cooler Hoses
A 15" & a 25" long line makes these kits ideal for those wanting to relocate the oil cooler!
Oil temperature sender unit housing for checking oil temperature.
Fits into the oil cooler hose.(Not compatable with braided hoses) Fitted before the oil cooler will show maximum temperature reached. After the oil cooler it will tell you the...
Whether you are installing a cooler from scratch or merely need to replace your tired old rubber hoses, you'll like the looks of this stronger Braided hose kit. The hoses are fully assembled, with the proper fittings in place and even include the nec...
A must for road use when an oil cooler is fitted.
In the past, fitting an oil cooler was mandatory once an engine had been even slightly uprated. The main reason for this was the quality of motor oils available at that time. If the oil temp...
Usefull joining union for 1/2" water hoses and used for oil coolers hoses.
The original union that fitted on the A series block to take the oil cooler hose. Many kits now include the union as part of the hose. Filter head size 1/4"NPT.
For minis from 1992 with a 12A engine. The block hose is 15" long and the filter hose is 22". The block has 11/16"UNF oil pipe hole thread.
These are the original brackets (2 required) used to fit on the front subframe to hold the oil cooler. For later cars check you have clearance.
SOLD INDIVIDUALLY.
It is critical to understand that an oil cooler is not designed to last the life of the car. Sound maintenance practice tells us that whenever we are doing a major engine overhaul we should not fail to replace the cooler as it is almost impossible to...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.