£33.86 exc vat
£40.63 inc vat
Out of stock
Please note;When fitting vented discs the metro drive flanges NAM6450F must be fitted. When assembling the caliper with the spacers for vented disc please use Locktite 243 on the threads and tighten to torque of 39nm. SPARE seals are 17H7680----If you require the Metric bolts for the brake discs to drive flange order SH110201M as they are not supplied in this kit.
£33.86 exc vat
£40.63 inc vat
Out of stock
Alloy Vented Brake conversion kit.
Only for use on existing caliper type hubs as used on Cooper S, 1275GT and all Minis from 1984 on. Requires 12" or 13" wheels to fit. The calipers are our alloy 4pot type
see kit [l...
Metro Turbo Vented Brake conversion kit.
Includes all parts to convert to Turbo brakes from drums. Car must be fitted with 12" wheels to fit.
Included in kit are hubs, bearings cv joints, swivel pins, brake discs, drive
fl...
Correct size and length brake pad pin for the caliper using 8.4" disc size and vented calipers.
PRICED INDIVIDUALLY per disc but should always be fittted in pairs for safety and efficiency..
THERE IS AN ALTERNATIVE GROOVED AND DRILLED PAIR OF DISCS SOLD AS C-GBD496.
Pair of 4-pot alloy calipers for 8.4" diameter brake discs with 12" (or bigger) wheels. Kit includes pad pins, but not brake pads.
The advantage of alloy calipers is that they dissipate heat quicker, reducing fluid boiling. The design a...
UK made 8.4" brake disc. Priced individually but should always be replaced in pairs for safety and braking efficiency. These are the best quality available of the low priced brake discs on the market and suitable for all standard road use.Beware of t...
Suitable for standard 8.4" / 7.5" /7" brake calipers. Also used for front wheel cylinders on twin leading shoe type drum brake cars. This is where you have 2 cylinders per hub as opposed to the early single leading type which had one cylinder only pe...
This is the small oil seal used on all Mini Spares 4 pot caliper and also the spacers fitted between Minispares 4 pot alloy when vented discs are fitted. They are supplied in the C-AJJ4021 kit to fit to our calipers when vented discs are...
High tensile 3/8" bolt 1.3125" long, to hold the standard calipers to the hub on disc brake models. Correct length shank and material. T grade 62 ton rating with vickers 287 reading-25-32 rockwell. The ERA turbo used Metro 4 pot calipers and used spe...
Pair of 4-pot alloy calipers for 7.5" diameter brake discs with 10" wheels. Kit includes pad retaining pins, but not brake pads. As used on Peter Baldwins mini
miglia challenge winning car for 3 years
Note: uses Metro pads which hav...
Genuine Lockheed seal rebuild kit for Cooper S brake calipers. One kit needed per caliper. When it comes to safety critical parts, only fit the original suppliers' parts as repair kits. The kit includes all the seals needed to do both pistons in one ...
Genuine oil seal between the two halves of the original cooper S caliper
and is only supplied by Rover. AP suggest you should buy the bolts to hold the 2 halves together as well when undertaking this repair, see 17H8765. Sold si...
metric 7mm bleed nipply as fitted to Metro calipers and rear wheel cylinders.
sold singly
Stainless steel "S" caliper piston for calipers that take 7.5"wide brake disc as used on all Cooper "S"variants and early 1275GT. These are correctly ground for long life and fitment against the seals,but nore importantly have the raised crown sectio...
Non spacered die cast alloy brake drums. The alloy material has a finned design that dissipates heat quicker which in turn helps reduce brake fade. Sold as a pair of drums.
Set of 6 hoses, 4 front and 2 rear to fit the ERA turbo.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided st...
Correct size and length brake pad pin for the caliper using 8.4" disc size and vented calipers.
Road use pads but for performance use C-AHT223GREEN these are original size 2.375" which fit later 997 cooper- but if you have the very early small pad type, 2.125" wide for 997cc less split pin holes, these are nearly obsolete you can g...
For use on 8.4" wide standard brake disc calipers, 2.920"wide.
This is the Ultimax upgrade which produces less brake dust which destroys alloy wheels. For the upgraded version of this see C-AHT16GREEN.
A set of split pins are availa...
A great street upgrade for 4 pot calipers giving off less brake dust and better efficiency.A set of split pins and metal retaining clips are available as GBK1025
Our favourite pads as the give less brake pad dust which destroys alloy wheels.
Very durable and great for most road usage. The green upgrade for fast street is C-8G8995GREEN.
For use with 4 pot calipers as per Metro or Minispares own alloy type these are our favourite road brake pads as the reduce contamination on alloy wheels by virtue of less brake pad dust, plus they work well with good anti fade properties. A set of s...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.