£4.28 exc vat
£5.14 inc vat
In stock
Also used for the oil filter head to block (pre spin on filter)
£4.28 exc vat
£5.14 inc vat
In stockRecommended usage 5 x CAM151 to fit one mini.
Correct latest spec head nut.Beware many sell an inferior nut.
Fitted to A Plus on, the built in flange of this latest specification multi point nut helps to spread the load and improve clamping force.
They may be used on any A-...
Standard A-series cylinder head retaining nut. For the later flanged nut see part number CAM4545.
This A type block 3/8" unc
stud to retain the cylinder head is 11/16"(17.3mm) longer than the standard 4" type with 1.5" of thread to hold brackets for other ancillaries such as coil. Usually fitted only at the heater tap end of the cylinde...
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:
Inlet/Exhaust manifold to head, studs/nuts/washers
Thermostat housing (no sandwich plate) studs/nuts/washers
H...
Minispares own stainless steel manifold stud and 6 sided hexagon nut kit.
For mutipopint nut kit see C-STR287
Quantity required one kit per car
Minispares own stainless steel Thermostat housing stud kit for the single tier type thermostat housing.Quantity required one kit per car
Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.
Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.
This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket
A true Cooper S engine has 10 studs and one specially designed bolt.
later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable
3/8"unc 1"long
replacements in stainless steel for the heater tap elbow on the cylinder head.
Quantity required one kit per car
Chrome Rocker bolt with UNF thread. Original Rocker cover bolts are dull zinc coated or painted but the chrome type look much better and cheaper.
A longer threaded version CAM6823 was used on prestige Minifin alloy type A series...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...
A simple way to dress up that engine compartment while at the same time insuring all the proper hardware is in place. A kit includes 2 each of British made chrome sleeve nuts, spacers and special cup washers, Fits all A & B series engines.
F...
Originally marketed by minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment they were improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. These T b...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.