17 TOOTH PINION FOR 3.7 RATIO
22A399

£24.00 exc vat

£28.80 inc vat

In stockIn stock
The 17 tooth pinion on the gearbox mainshaft to drive the 3.65 1100 (ADO16 cars) and 3.76 early mini crownwheels.

£24.00 exc vat

£28.80 inc vat

In stockIn stock

Recommended usage 1 x 22A399 to fit one mini.
A Type Gears - Qty 1
B Type 3 Synchro Mesh Gears - Qty 1
4 Synchro Gears Up to 1979 with 14MM Nose Mainsha - Qty 1
Final drive ratios and Five Speed Gearbox - Qty 1
Final drive ratios and Five Speed Gearbox - Qty 1

Kit products

62 tooth crownwheel and 17 tooth pinion pre Aplus

People also bought products

the Pre A Plus 16 tooth pinion gear for the 3.9 ratio diff

62 tooth crownwheel and 17 tooth pinion pre Aplus

19 tooth pinion for 3.1 and 3.2 final drives with 3 groove mark

list below for other markings

17 teeth central groove

18 teeth offset groove to one edge

19 teeth 3 groove markss

Fits all minis except Autos and those with hardy spicer joints. It has the detent lug on for rod change R/H side. Sold singly.

These might be marked as 22G420 on the casting but they have the correct size bush and seal hole for...

Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...

The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.

A bronze type bush that fits in the gearbox output shaft side cover on early automatics and Cooper S with hardy spicer type joints. These are larger than the standard mini or rod change engine gearbox types which take 2A3538.

This is the original Evolution"Cross-pin" differential for the Mini.

Produced and sold by Mini Spares since 1994. It is a super heavy duty differential designed as a significant upgrade for reliability and strength to the standard units. Ove...

Planet gears for the differential are now manufactured by us as the genuine Rover product is obsolete. Beware of others on the market which must be checked before fitting as the overall dimensions in height seem to vary along with inferior/wrong mate...

You will need to shim up your diff bearings with these washers as required. See workshop manuals for details. See also DAM3109 & DAM3633.

The gearbox diff side plate bonze colour bush for all except auto and cooper S with hardy spicer output shafts. Sold singly 2 required per gearbox.

clearance needs to be 0.03mm

This is an aftermarket high tensile shouldered bolt that engine and gearbox tuners are using, as the original shape head and high tensile type bolt is no longer available. For holding the crown wheel to the differential housing.

Sold individ...

All differential crownwheels used these locktabs. 3 required and if you need new bolts see ATA7043 (6 of.) All sold singly

Genuine Rover are now 48 thou thick which is so tight they can lock up your differential. The originals were .035 thou. These are machined down to be exactly the correct size required but we also stock oversize 43 thou type which are available as [li...

See DAM3108 also for smaller diff shims. Refer to workshop manual for fitment.

The latest model Mini differential still use thrust washers on the spider gears but now have a tab on one end to prevent them from rotating on the cage side of the diff. The cage of course is cast while the gear itself is much harder and thus the wh...

Bolt for holding the Clutch End cover (Wok) onto the flywheel housing.

Also for the CHM85 differential side cover 1" long unc 5/16" bolt.

A plus type bolt with built in washer on head, known as flanged head bolt.

Genuine Rover Tuftrided diff pin, as fiited to all the later A+ gearboxes as a standard upgrade. These are the last genuine parts left and will not be available again

Bronze type bush is in the centre of all crownwheels in the gearbox plus another one is in the differential case opposite the end the crownwheel fits.

The bush after fitting will need to be reamed. Ream to 26.16mm 1.03"