£727.83 exc vat
£873.40 inc vat
Out of stock
No matter how well your Mini handles, you still have to stop sometime, and if the car in front of you has ABS you'd better be able to stop right now! At one time the only way to get ...
£727.83 exc vat
£873.40 inc vat
Out of stock
UK made-Rear brake drum on all post 1984 cars plus the Mini Cooper "S" 1275GT models which has a built in spacer ( 1") and uses standard 1 1/4" shoes (GBS834AF). It will also fit the front or rear of a non-S Mini, with 1 1/4" shoes or (1 1/2" shoes G...
This is the correct length for all minis using the rear spacered type drum which was fitted to all Cooper "S" 1275GT and every mini from 1984 to 1996 except the ERA Turbo and Sportspac cars which had 13" wheels. Stud shank length from under head of b...
If your rear brake drums have 1" built in spacers such as all Cooper S and any post 1984 minis, these are the longer drum retaining screws, 2 required per drum and sold individually.
Cooper S 7.5" complete brake disc kit, except for disc shields, with genuine AP calipers and Tinken bearings. If you want or have 10" wheels this is the kit to convert from drum brakes to discs brakes. See C-AJJ4028MS for kit with our ow...
Cooper S 7.5" complete brake disc kit, except for disc shields, with Mini Spares own cast standard calipers. If you want or have 10" wheels this is the kit to convert from drum brakes to discs brakes.
This kit includes every nut bolt and co...
These copper sealing washers should be replaced every time the hoses are undone as a precaution. 10mm i/d, 15mm o/d. is smaller than a 3H550
Original genuine sintered split washer for behind the hub nut that goes on the cv joint drive flange.
This is not the cheap old metal type often sold by our competitors which Rover discontinued and changed to sintered for all production car...
Front genuine Timken wheel bearing kit for one hub only. Kit comes complete with split pins and inner and outer hub seals.If you suffer from wheel bearing problems check the hub for wear which is usual and use best quality cv joints.
Genuine...
Countersunk crosshead screw. 1/4"unf / 16mm(3/8") total length.
To hold the drive flange to the brake disc on the Cooper S type 7.5" wide brake set up. Also holds striker plate for door.
Mini Spares own stamped GCV1013. Brand new CV Joints with gaiter, hub nut, grease and clips. Stamped with our part number GCV1013 for identification from may 2014 to denote our authenticity of this top quality joint, sold singly.
These are t...
Pair of 4-pot alloy calipers for 7.5" diameter brake discs with 10" wheels. Kit includes pad retaining pins, but not brake pads. As used on Peter Baldwins mini
miglia challenge winning car for 3 years
Note: uses Metro pads which hav...
Genuine Minispares approved joints that we have supplied since 2004-
Beware of spurious products on the market as these are a safety critical part.
BEWARE OF CURRENT SO CALLED GENUINE ITEMS AS THEY ARE NOT FIT FOR PURPOSE.
...
Minispares own product-R/H to last Rover drawings and supplied to us by a UK Heritage specialist. Originally the BMC castings were machined by Portland Eng but in the 90's we put down tooling with IVRA in Italy who had them manufactured by Torme in I...
Mini Spares standard road use disc 7.5" wide using material GG25EURO.
These were standard fitment on all Cooper S models plus early 1275GT made from OE drawings to the correct material spec. Cheaper types on the market that we have tried sin...
Always check these grease nipples on your front hubs are working as they are very important. These two swivel pin grease nipples are the same, upper and lower. Also used on the rear radius arms. Sold individually.
these are top quality greas...
Mini Spares own quality product from original drawings in EN24 material for 7.5" wide disc set ups.
The Mini Cooper "S" drive flange as used on all 7.5" disc Cooper S/1275GT variants was originally intended to use 10" wheels as an integral p...
Minispares own product-L/H, to last Rover drawings and supplied to us by a UK Heritage specialist. Originally the BMC castings were machined by Portland Engineering but in the 90's we put down tooling with IVRA/Italy who had them manufactured by Torm...
A great street upgrade for 4 pot calipers giving off less brake dust and better efficiency.A set of split pins and metal retaining clips are available as GBK1025
A great street upgrade for 4 pot calipers giving off less brake dust and better efficiency.A set of split pins and metal retaining clips are available as GBK1025
For use with 4 pot calipers as per Metro or Minispares own alloy type these are our favourite road brake pads as the reduce contamination on alloy wheels by virtue of less brake pad dust, plus they work well with good anti fade properties. A set of s...
12" wheel to 10" wheel running gear conversion kit. Less wheels.
This kit will convert your 8.4 disc set up to the Cooper S 7.5 discs to allow fitment of 10" wheels, kit includes discs, calipers, kevlar pads with split pins and drive flanges...
7.5" Vented brake disc, suitable for use with our vented alloy 4 pot calipers (C-AJJ4023 together with C-AJJ4021). These are sold individually but should always be replaced in pairs. These are in fact 8.4" vented discs machined down
to 7.5" ...
Genuine AP brand new rear Left Hand back plate assembly (beware of copies).
These are ready to bolt on, brand new stock from AP Automotive and have the .75" bore genuine wheel cylinders GWC1102. Remember that all wheel cylinder ...
Genuine AP brand new rear right hand back plate kit (beware of copies).
These are ready to bolt on brand new stock from AP Automotive and have the .75" bore genuine wheel cylinders GWC1102. Remember that all wheel cylinder rubb...
If your rear brake drums have 1" built in spacers such as all Cooper S and any post 1984 minis, these are the longer drum retaining screws, 2 required per drum and sold individually.
Correct size and length brake pad pin for the caliper using 7.5" disc size as fitted to Cooper S and 1275GT. 4 required for 1 car, also fits Cooper 7" calipers. 3mm diameter.
A pair of L/H shield covers for 7.5" disc as fitted to Cooper S
The little locating bracket to the hub is available seperate as BTA1209
The screw that holds the drum on the hub. Earlier hubs had two screws, many replacements have only one, all that’s needed.
Split pin for the larger size CV joint as fitted to disc brakes. This pin is usually supplied in our normal stock bearing kits. Sold individually.
this will also fit the nut for the rubber cross drive coupling on the gearbox
Mintex brake shoes for the rear of all minis which are 1.25" wide. Also fitted to front on early single leading shoe cars (dry suspension pre 1964) with a single wheel cylinder. Manufactured by Mintex and sold as a box set of 4 brake shoes for one re...
8.4" diameter as used standard on all late model Minis with 12 or 13 inch wheels. Our premium quality item. See GBD90806MS for a cheaper option.
Sold individually, but should be replaced as pairs.
A pair of r/h disc shield covers for 7.5"wide brake discs as per cooper S
If you require the little bracket order seperate as BTA1208
Cooper S disc brake water shields are easily damaged and hence frequently missing altogether. A complete kit consists of six different components: upper and lower shields plus mounting tabs for each side. Complete set is 21A1271, [link]2...
Cooper S disc brake water shields are easily damaged and hence frequently missing altogether. A complete kit consists of six different components: upper and lower shields plus mounting tabs for each side. Complete set is 21A1271, [link]2...
Mini Spares standard road use disc 7.5" wide using material GG25EURO.
These were standard fitment on all Cooper S models plus early 1275GT made from OE drawings to the correct material spec. Cheaper types on the market that we have tried sin...
12" wheel to 10" wheel running gear conversion kit. Less wheels
this kit will convert your 8.4 disc set up to the original Cooper S 7.5 discs to allow fitment of 10" wheels, kit includes discs, calipers, pads with split pins and drive flange...
Cooper S disc brake water shields are easily damaged and hence frequently missing altogether. A complete kit consists of six different components: upper and lower shields plus mounting tabs for each side. Complete set is 21A1271, [link]2...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.