£380.00 exc vat
£456.00 inc vat
In stock
The cone spring platform had 2 extra bracktets either side to act as reinforcements and the platform hole has a bottoming out metal plug fitted.
For an exact Mini Spares non genuine item see MS45LATE which are endorsed by our Potters Bar staff members who have fitted them to their cars.
£380.00 exc vat
£456.00 inc vat
In stockRecommended usage 1 x KHB100590 to fit one mini.
E coated Mini Spares product. This non genuine dry suspension subframe has the metal prongs/hangers for rubber strap type mounts as fitted from 1990 cars. Supplied in superb looking E-coat finish for longevity, with strengthening brackets as per MPI ...
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 can use the same bush (2A5818/POLY) at the front and rear of the subframe, ...
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 used the same bush 2A5818(C-STR638) at the front and rear of the subframe, ...
Complete set of bolts to mount the front subframe on all post 76 single bolt subframes less the large tower bolts and towing eye, enough fixings are supplied for those who wish not to use a towing eye.
Original pin that the rear subframe bushes sit on inside the trunnions on the rear subframe of every mini ever made. See {link}21A1440MS[/link] for Mini Spares better quality item
Minis Spares product to a slightly higher modern day shore hardness and texture soecification.
Pre 1976 used 8 of these bushes for the trunnions on the rear subframe but from (MK4)1976 on Rover reduced the quantity to 4 and used 2 larger bus...
complete kit of bushes and bolts for pre 1976 rear subframes when 8 rubber bushes the same size are used--for cars after 1976 with 4 small and 2 large rubber bushes use MS43
Rubber mounts are made in the UK.
Mini Spares product is a better quality pin-Please note that only the pin is supplied. Please see 2A5818MS for the bushes.
2 required per car
The correct screw for holding the 2A4267MS bump stop for the upper arm on the front suspension. 3/16"unf 1/2"long flat head phillips type screw.
Every nut, washer, bolt, rubber bush and 2 pins that hold the rubber bushes that are prone to rusting badly and are required every time you do a subframe change. Including the 2 large penny washers this kit has 36 components. Other companies offer l...
Some cars left Rover with the tie rod locating plate welded to far back on the R/H side which causes the car to pull to the left. We have found this on over 4 cars that had definately no accident history. The only difference between this twin point i...
Priced each, 2 of these are fitted to the rear of the front subframe on all cars from 1976 on. These original rubber type can be replaced by alloy or other equivalents, see our accessory catalogue. ALSO SEE 21A2599MS.
Genuine metal trunnion to hold the 2-2A5818MS bushes on the rear subframe. Originally there were 4 of these on the subframe but in 1976 the front 2 brackets were strenghened and enlarged to 21A2558 trunnion which took one large single bu...
This is the real way to go if you want to make your front subframe solid mounted in metal components to replace the rubber set up on the front subframe from 1976 on
The gasket that sits behind the door stiker on all wind up window type minis
on the B post.
MK3 Door & boot handle fitting kit, including original type screws, star washers and gaskets.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.