5 SPEED CLOSE RATIO HELICAL GEARBOX WITH ATB PIN 3...

MSG03-ATB

£4,040.76 exc vat

£4,848.91 inc vat

Special order

New for 2023, special heavy duty 2nd and 3rd gears with laygear and 1st motion to match giving a quiet road box suitable for engines producing upto 125lbft of torque on naturally aspirated engines.

Ratios are:

1s...

£4,040.76 exc vat

£4,848.91 inc vat

Special order

Recommended usage 1 x MSG03-ATB to fit one mini.

Kit contained products

MAINSHAFT / THIRD MOTION SHAFT LATE TYPE

DAM7484

A plus mainshaft. 18mm (11/16")nose bearing type.

The earlier mainshaft pre A plus is22G833

This shaft uses DAM7485

£117.02 exc vat

£140.42 inc vat

THIRD GEAR RETAINING WASHER AND 5TH GEAR FOR 5 SPE...

22G947

Special locking washer for 3rd gear on 4 synchro gearboxes plus our own 5 speed 5th gear. The washer for 2nd gear is 22G839

£13.88 exc vat

£16.66 inc vat

SYNCHRO HUB SPRING. 4 SYNCHRO ONLY

22G2262

Only for the 4 synchromesh gearbox synchroniser gear hub. There are 3 of these per hub with BLS107 ball bearing.

£1.05 exc vat

£1.26 inc vat

CROWNWHEEL 62 TOOTH FOR 3.4 RATIO PRE A PLUS

22A411

The crownwheel for 3.4 ratio as fitted to most Cooper S and many other variants. Early 850 minis usually had 3.76 ratio.

Later on Rover fitted 2.9/3.1 and 2.76 ratios.

Needs 22A413 18 tooth pinion.

£132.00 exc vat

£158.40 inc vat

OIL PIPE HITECH CENTRAL PICKUP GEARBOX

C-AHT54

Minispares recommend this central oil pick-up be installed with every transmission rebuild.

The original Mini oil pick-up pipe lives in the right hand edge of the gearbox casing, which is okay if you are driving straight. But during a right ...

£23.50 exc vat

£28.20 inc vat

REVERSE DETENT O RING ROD CHANGE/BAU5043 SEAL

22G1417

This o ring goes on the detent plunger located behind the gearbox output shaft side plates on all Rod change gearboxes. See also BLS110 ball & 22G2083 spring. Also fit BAU5043 heater matrix.

£0.26 exc vat

£0.31 inc vat

CROWNWHEEL PINION 18 TOOTH FOR 3.4 RATIO PRE A PLU...

22A413

The favourite final drive for minis this is the pre A plus type which was stronger and fitted to Cooper S etc. goes with 22A411 crownwheel.

£60.80 exc vat

£72.96 inc vat

REVERSE GEAR BUSH

TUJ10001

The longer one piece bush as fitted to all late reverse gears. Early type had 2 single bushes which sometimes came adrift after arduous use.

£4.50 exc vat

£5.40 inc vat

DIFF CROWNWHEEL LOCKTAB

ATA7385

All differential crownwheels used these locktabs. 3 required and if you need new bolts see ATA7043 (6 of.) All sold singly

£2.05 exc vat

£2.46 inc vat

DIFF SHIM 10 THOU

DAM3109

See also DAM3108.

£0.83 exc vat

£1.00 inc vat

DETENT SPRING FOR ROD BOX

22G2083

When you take the side cover off the differential housing on a rod change type gearbox this detent ball spring sits on a ball bearing BLS110 and the sleeve is 22G1870. The oil seal for this is 22G1417.

£0.27 exc vat

£0.32 inc vat

ROLLER DOUBLE FOR MAINSHAFT IN GEARBOX. RHP GENUIN...

AAU1365

Genuine RHP bearings. Not cheap Imported rubbish as sold under this part number.

This is the workhorse of the Mini gearbox. This double roller bearing supports the shaft where it transmits the power to the wheels. When this bearing goes, the...

£54.14 exc vat

£64.97 inc vat

DIFF OUTPUT SHAFT OIL SEAL

ADU5738

Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.

Upgraded version in Viton available us ADU5738VITON

£0.91 exc vat

£1.09 inc vat

DIFF SHIM 6 THOU

DAM3108

You will need to shim up your diff bearings with these washers as required. See workshop manuals for details. See also DAM3109 & DAM3633.

£0.79 exc vat

£0.95 inc vat

GEARBOX DIFF SIDE PLATE GASKET GENUINE MINISPARES

GUG705567GM

Try these GENUINE MINISPARES superseal gearbox output shaft gaskets specially made to try and eliminate leaks.

Sold singly,2 per gearbox

£2.03 exc vat

£2.44 inc vat

IDLER NEEDLE ROLLER FOR A PLUS GEARBOX

TUK100320

Torrington/Koyo idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior...

£8.25 exc vat

£9.90 inc vat

GASKET DIFF UPPER

2A3505B

The upper differential housing gasket for all minis. The lower gasket for rod change gearboxes is 22G1836 and for remote use 2A3506B.

£0.25 exc vat

£0.30 inc vat

SEAL UNDER ROD CHANGE SELECTORS TO GEAR CASE

31B447

Often overlooked when doing gearbox rebuilds this seal is very important as it sits in the very bottom of the case and is the source of irritating oil leaks.

The large round metal plug in the bottom of the gearbox is the pivot pin for all th...

£0.30 exc vat

£0.36 inc vat

GASKET SPEEDO HOUSING INSPECTION GASKET

GUG705564GM

for the inspection plate on the front cover of the transmission where the speed cable goes to -it has 2 bolt holes cut out

£0.48 exc vat

£0.58 inc vat

BALL BEARING FOR SYNCHRO HUB 3&4 SYNCHRO

BLS107

Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.

£0.45 exc vat

£0.54 inc vat

GEARBOX OIL PICK UP PIPE GASKET

22A542B

Gearbox oil strainer to gearbox internal case gasket and also used on the C-AHT54 special oil pick up pipe. One also sits on the outer plate held onto the gearbox outer casing by 2 screws.

£0.24 exc vat

£0.29 inc vat

GASKET DIFF LOWER.PRE ROD

2A3506B

Lower differential housing paper gasket for old magic wand and remote type gearboxes, rod change gearboxes.

£0.27 exc vat

£0.32 inc vat

FIRST GEAR 4 SYNCHRO ALL MODELS 31 teeth

22G1096

Every 4 synchro gearbox had a straight cut first gear as standard.

This one has 31 teeth and beware complete straight cut race gears sets use a 29 different tooth count.

£105.00 exc vat

£126.00 inc vat

DIFFERENTIAL ROLLER RHP manufacture

AHU1856

Genuine RHP as originally fitted to every production Mini.

Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.

Some original fi...

£28.29 exc vat

£33.95 inc vat

COMPETITION STEEL BAULK RING

C-22A1741

Mini Spares Performance Baulk ring.

The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...

£35.36 exc vat

£42.43 inc vat

SINGLE ROW RHP ROLLER. 4 SYNCHRO

ADU7619

Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.

This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...

£34.97 exc vat

£41.96 inc vat

LAYSHAFT A PLUS PERFORMANCE

C-22A1739

Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...

£31.85 exc vat

£38.22 inc vat

SWIFTUNE CLASSIC MINI QUAIFE ATB DIFFERENTIAL

C-AJJ3390

The Swiftune classic Mini Quaife ATB Automatic Torque Biasing differential offers the benefits of an LSD limited slip differential but saving you money on crownwheels and pinion plus output shafts!!

The Swiftune Quaife ATB avoids the need fo...

£679.00 exc vat

£814.80 inc vat