£29.25 exc vat
£35.10 inc vat
In stock
It fits to the thermostat housing and end manifold stud and also onto the bulkhead where the heater pipes go through. For 850, 998, and 1100, see MSSK1000.
£29.25 exc vat
£35.10 inc vat
In stockRecommended usage 1 x MSSK1300 to fit one mini.
Forget all the universal shape gaskets available - this is the original correct shape made out of thick gasket paper.
A "must have" for every car. All the torque action of the motor is controlled by the stabilizer arm located just above the flywheel housing. If you are still using original type rubber bushes you are living in the past. Our uprated kit includes four ...
The last Rover update on the upper engine stabiliser bar, but this is upgraded for performance use.
A one piece silent block type bush, it was fitted at both ends from 1996 on and will fit any cars that had 2 bushes fitted at either end as o...
For 1275cc engines with sandwich plate fitted except when PEQ10019 large bore thermostat housing is fitted.(fitted to HIF carb models between 1990-91). It has been used for these models however by extensive modifying around the horseshoe...
Original genuine standard tie bar bush (2 per rod) but sold individually.
These bushes are made to the original drawing and specifications by the original manufacturing company for BMC/Leyland & Rover.
These genuine bushes are soft ...
The last Rover update on the upper engine stabiliser bar, but this is upgraded for performance use.
A one piece silent block type bush, it was fitted at both ends from 1996 on and will fit any cars that had 2 bushes fitted at either end as o...
Lower Stabilizer Kit, RH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In stock form the control is left to the upper stabilizer. This often results in not o...
The poly version of the upper engine stabiliser arm bush is used in our kit C-STR630. Please note colour may be different from that shown.
Sold per bush but fitted in pairs.
Adjustable engine upper stabiliser rod.
Copy of ERA 1020 adjustable rod as fitted to the ERA mini turbo for clearance reasons. This adjustable rod takes the standard rubber bushes or equivalent and is a useful means of pushing the top of the...
The original stabiliser kit with cone shaped spacers to strengthen up the rubber bushes against engine movement. Kit includes 4 cone metal shaped inserts and 4 bushes. When stocks run out only the plastic insert type kit SBK1 will be ava...
The original stabiliser kit with cone shaped spacers to strengthen up the rubber bushes against engine movement. Kit includes 4 cone plastic shaped inserts and 4 bushes. The cone shaped inserts push the rubber out in the middle of the engine steady b...
Extra hard bushes for competition use. All the torque action of the motor is controlled by the stabilizer arm located just above the flywheel housing. If you are still using original type rubber bushes you are living in the past. Our uprated kit incl...
A "must have" for every car. All the torque action of the motor is controlled by the stabilizer arm located just above the flywheel housing. If you are still using original type rubber bushes you are living in the past. Our uprated kit includes four ...
This lower engine steady rod was fitted as standard when a welded bracket was added to the front of the front subframe in 1989. The other end bolted to the gearbox by bracket NAM3760. The fixed rod is obsolete from Rover, but this adjust...
The steady rod that is Right Hand lower on the gearbox and is part of our lower engine stabilser kit MSSK.
This bush is a genuine version of CRC5329 and sold individually.
There are 2 of these bushes fitted at either end of the engine stabiliser on all cars upto 1996 except some very early cars which had large single bushes fitted. F...
The last Rover update on the upper engine stabiliser bar.
A one piece silent block type bush was fitted at both ends from 1996 on and will fit any cars that have 2 bushes fitted at either end as original.
These have also been fitted...
Engine stabiliser arm to block bolt. This is the longer bolt that fits the engine stabiliser rod to the cylinder block.
Used in our MSSK001 left hand lower engine stabiliser kit this bracket fits to the subframe and the gearbox.
This upper engine steady rod was fitted as standard to the Austin 1100/1300 range of 4 door cars and then fitted to the 1275CC minis from 1990 on, to position the engine half an inch (12.7mm) further forward to help clearance for the carbs and inject...
For 1275cc engines with sandwich plate fitted except when PEQ10019 large bore thermostat housing is fitted.(fitted to HIF carb models between 1990-91). It has been used for these models however by extensive modifying around the horseshoe...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.